Mitsubishi L200. Manual — part 663
IGNITION SWITCH
CHASSIS ELECTRICAL
54A-19
STEP 7. Voltage measurement at C-301 key
reminder switch connector
(1) Disconnect the connector, and measure at the
wiring harness side.
(2) Voltage between C-301 power window main
switch connector terminal No.2 and body earth.
OK: System voltage
Q: Is the check result normal?
YES :
Go to Step 9.
NO :
Go to Step 8.
AC903858AB
Harness side
Connector: C-301 <LHD>
AC903869AB
Harness side
Connector: C-301 <RHD>
AC402679
Connector C-301
(Harness side)
CA
IGNITION SWITCH
CHASSIS ELECTRICAL
54A-20
STEP 8. Check the wiring harness from C-301 key
reminder switch connector terminal No.2 to
fusible link (20).
Check the power supply line for open circuit.
NOTE:
Prior to the wiring harness inspection, check joint
connectors C-132, and junction block connector C-
209 and C-213, and repair if necessary.
Q: Is the check result normal?
YES :
Go to Step 11.
NO :
Repair the wiring harness.
AC903858AB
Harness side
Connector: C-301 <LHD>
AC903869AB
Harness side
Connector: C-301 <RHD>
AC903853
Connector: C-132 <LHD>
AC
C-132 (GR)
AC903865
Connector: C-132 <RHD>
AB
C-132 (GR)
AC509934
Connectors: C-209, C-213 <LHD>
Junction block (Front view)
C-213
C-209
C-213
C-209
AC
Harness side
Harness side
AC509936
Connectors: C-209, C-213 <RHD>
C-213
C-209
AC
Junction block
(Front view)
C-213
C-209
Harness side Harness side
IGNITION SWITCH
CHASSIS ELECTRICAL
54A-21
STEP 9. Connector check: C-219 ETACS-ECU
connector
Q: Is the check result normal?
YES :
Go to Step 10.
NO :
Repair the defective connector.
STEP 10. Check the wiring harness from C-219
ETACS-ECU connector terminal No.62 to C-301
key reminder switch connector terminal No.1.
Check the input line for open circuit or short circuit.
Q: Is the check result normal?
YES :
Go to Step 11.
NO :
Repair the wiring harness.
AC509934
Connector: C-219 <LHD>
CU
C-219 (GR)
Harness side
Junction block (Front view)
AC509943
Connector: C-219 <RHD>
AB
C-219 (GR)
Harness side
Junction block
(Rear view)
AC509934
Connector: C-219 <LHD>
CU
C-219 (GR)
Harness side
Junction block (Front view)
AC509943
Connector: C-219 <RHD>
AB
C-219 (GR)
Harness side
Junction block
(Rear view)
AC903858AB
Harness side
Connector: C-301 <LHD>
AC903869AB
Harness side
Connector: C-301 <RHD>
IGNITION SWITCH
CHASSIS ELECTRICAL
54A-22
STEP 11. Retest the system.
Check that the ignition key cylinder illumination lamp
illuminates or extinguishes normally.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
Cope with Intermittent Malfunction ).
NO :
Replace the ETACS-ECU and register the
ID codes (Refer to
Inspection Procedure 2: Malfunction of the ignition switch power supply system
CAUTION
Whenever the ECU is replaced, ensure that the
input and output signal circuits are normal.
COMMENTS ON TROUBLE SYMPTOM
When the power supply system of ignition switch has
a problem, none of the equipment and system con-
nected to the ignition switch works even if the ignition
switch is operated.
POSSIBLE CAUSES
• Malfunction of the ignition switch
• Damaged harness wires and connectors
IGNITION
SWITCH
FUSIBLE
LINK
3
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Grey R : Red P : Pink V : Violet PU : Purple SI : Silver
Ignition Switch Power Source Circuit
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст