Mitsubishi L200. Manual — part 806
DIAGNOSIS CODE PROCEDURES
LOCAL INTERCONNECT NETWORK (LIN)
54B-35
STEP 5. Check the wiring harness between E-06
rear power window sub switch (RH) connector
terminal No. 4 and the power window relay
AC502334AD
Harness side
Connector: E-06
Check the power supply line for open circuit and
short circuit.
NOTE:
AC903853
Connector: C-16 <LHD>
AL
AC903868
Connector: C-16 <RHD>
AQ
AC903856
Connectors: C-32, C-33 <LHD>
AJ
C-33
C-32
C-33
C-32 (GR)
AC903865
Connectors: C-32, C-33 <RHD>
AE
C-33
C-32 (GR)
C-32
C-33
AC901129
Connector: D-24
AH
Prior to the wiring harness inspection, check interme-
DIAGNOSIS CODE PROCEDURES
LOCAL INTERCONNECT NETWORK (LIN)
54B-36
diate connectors C-16, C-33, D-24 and joint connec-
tor C-32, and repair if necessary.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
use Troubleshooting/inspection Service
Points
− How to Cope with Intermittent
Malfunction ).
NO :
Repair the wiring harness.
DIAGNOSIS CODE PROCEDURES
LOCAL INTERCONNECT NETWORK (LIN)
54B-37
STEP 6. Check the wiring harness between C-219
ETACS-ECU connector terminal No.54 and E-06
rear power window sub switch (RH) connector
terminal No.6.
AC509934
Connector: C-219 <LHD>
AD
C-219 (GR)
Harness side
Junction block
AC502334AD
Harness side
Connector: E-06
NOTE:
AC903853
Connector: C-16 <LHD>
AL
AC903868
Connector: C-16 <RHD>
AQ
AC901129
Connector: D-24
AH
Prior to the wiring harness inspection, check interme-
diate connectors C-16 and D-24, and repair if neces-
sary.
• Check the communication line for open circuit.
Q: Is the check result normal?
YES :
Go to Step 7.
NO :
Repair the wiring harness.
STEP 7. Check whether the diagnosis code is
reset.
Check again if the diagnosis code is set to the
ETACS-ECU.
(1) Erase the diagnosis code.
(2) Turn the ignition switch from "LOCK" (OFF)
position to "ON" position.
(3) On completion, check that the diagnosis code is
reset.
Q: Is the diagnosis code set?
DIAGNOSIS CODE PROCEDURES
LOCAL INTERCONNECT NETWORK (LIN)
54B-38
YES :
Replace the rear power window sub switch
(RH).
NO :
A poor connection, open circuit or other
intermittent malfunction is present in the LIN
bus lines between the rear power window
sub switch (RH) and the ETACS-ECU
(Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
−
How to Cope with Intermittent Malfunctions
).
Code No.U1512: Rear panel power window-ECU time-out
Rear Panel Power Window LIN Communication Circuit
LIN
INTERFACE
ECU
REAR PANEL
POWER WINDOW-ECU
ETACS-
ECU
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Grey R : Red P : Pink V : Violet PU : Purple SI : Silver
FUSE
2
RELAY
BOX
TROUBLE JUDGEMENT
The ETACS-ECU receives signal from the rear panel
power window-ECU. If signal cannot be received at
all, diagnosis code No.U1512 will be set.
COMMENT ON TROUBLE SYMPTOM
The M.U.T.-III shows a diagnosis code status as
active.
• Connector(s) or wiring harness in the LIN bus
lines between the rear panel power window-ECU
and the ETACS-ECU, the power supply system of
the rear panel power window-ECU, or the rear
panel power window-ECU itself may be defective.
The M.U.T.-III shows a diagnosis code status as
stored.
• If diagnosis code No.U1512 is stored as a past
trouble, carry out diagnosis with particular
emphasis on wiring and connector(s) in the LIN
bus line between the rear panel power window-
ECU and the ETACS-ECU, and the power supply
system of the rear panel power window-ECU. For
diagnosis procedures, refer to GROUP 00, How
to Use Troubleshooting/Inspection Service Points
− How to Treat Past Trouble .
PROBABLE CAUSES
• Malfunction of the rear panel power window-ECU
• Damaged harness wires and connectors
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст