Mitsubishi L200. Manual — part 694
HEADLAMP
CHASSIS ELECTRICAL
54A-143
HEADLAMP BULB (HIGH-BEAM)
REPLACEMENT <VEHICLES FOR
EUROPE (EXCEPT FOR SINGLE CAB)>
CAUTION
Do not touch the bulb surface with bare hands or
dirty gloves. If the bulb surface (glass part) gets
dirty, immediately clean it with alcohol or thinner.
After drying completely, install the bulb.
Disconnect the connector, and twist the headlamp
bulb (high-beam) to remove.
POSITION LAMP BULB REPLACEMENT
Disconnect the connector, and twist the position
lamp socket to remove it.
FRONT TURN-SIGNAL LAMP BULB
REPLACEMENT
Disconnect the connector, and twist the front turn-
signal lamp socket to remove it.
HEADLAMP AUTOMATIC-SHUTDOWN
FUNCTION CHECK
M1540100800026
Confirm that the headlamp turns off when the ignition
switch is ON and the driver's door is opened and
when the ignition key is pulled out with the lighting
switch at ON (HEAD) position and the driver's door is
opened. If not, carry out the troubleshooting. (Refer
to
.)
HEADLAMP AUTO LAMP FUNCTION
CHECK
M1540100900261
Verify that the headlamps will illuminate when plac-
ing a hand over the light receiver of the lighting con-
trol sensor under direct sunlight with the ignition
switch in the "ON" position and the lighting switch in
the "AUTO" position. If there is a malfunction, per-
form the troubleshooting (Refer to
NOTE: When covering the lighting control sensor
receiver, be careful not to touch the windshield sur-
face (where the lighting control sensor receiver is
mounted). (The lighting control sensor receiver has
limited resistance to oil.)
AC800990AG
Headlamp bulb (High-beam)
<Vehicles for Europe (except for single cab)>
AC900629AD
Position lamp
<Single cab and vehicles for Russia>
AC800990AH
Position lamp
<Vehicles for Europe (except for single cab)>
AC900629AE
Front turn-signal lamp
<Single cab and vehicles for Russia>
AC800990 AI
Front turn-signal lamp
<Vehicles for Europe (except for single cab)>
HEADLAMP
CHASSIS ELECTRICAL
54A-144
CUSTOMISATION FUNCTION
M1540103701087
The following functions can be customised using
M.U.T.-III.
Function
Item name
Configuration
Turn-signal lamp operation sound
function
Turn-signal lamp buzzer
• Operation: Standard tone (Initial
setting)
• Operation (type A): Differs from
standard tone
Comfort flashing function
Comfort flashing
function
• Inhibit (initial condition)
• Operation
Headlamp automatic-shutdown function Headlamp automatic-
shutdown
• Not operation
• B-spec (initial condition)
Hazard lamp blink time of keyless entry
hazard lamp answerback function
<vehicles with keyless entry system>
Hazard answer-back
• Lock 1 Unlock 2 (initial condition)
• Lock 1 Unlock 0
• Lock 0 Unlock 2
• Lock 2 Unlock 0
• Lock 0 Unlock 0
Auto lamp function sensor sensitivity
(illumination intensity) <vehicles with
auto lamp>
Sensitivity for auto
lamp(RLS)
• Level 1 bright
• Level 2 bright
• Level 3 (Initial setting)
• Level 4 dark
• Level 5 dark
HEADLAMP
CHASSIS ELECTRICAL
54A-145
HEADLAMP REMOVAL AND INSTALLATION
M1540101000733
<SINGLE CAB AND VEHICLES FOR RUSSIA>
Post-installation operation
Check the beam direction of the headlamp (Refer to
Headlamp Aiming
).
AC809114AB
2
4.9 ± 0.7 N·m
3
4
5
6
7
8
9
10
2.5 ± 0.3 N·m
4.9 ± 0.7 N·m
2.5 ± 0.3 N·m
1
Headlamp levelling switch
removal steps
•
Lower panel assembly (Refer to
GROUP 52A, Instrument Panel
Assembly ).
1.
Headlamp levelling switch
Headlamp removal steps
2.
Headlamp bulb socket cover
3.
Headlamp bulb
4.
Position lamp bulb socket
5.
Position lamp bulb
6.
Front turn-signal lamp bulb socket
7.
Front turn-signal lamp bulb
Headlamp body removal step
•
Radiator grille (Refer to GROUP
51, Radiator grille .)
•
Front splash shield (Front bumper
side) (Refer to GROUP 42, Splash
shield ).
8.
Headlamp body
9.
Grommet
10. Headlamp bracket
Headlamp removal steps
HEADLAMP
CHASSIS ELECTRICAL
54A-146
<VEHICLES FOR EUROPE (EXCEPT FOR SINGLE CAB)>
Post-installation operation
Check the beam direction of the headlamp (Refer to
Headlamp Aiming
).
AC807115
3
4.9 ± 0.7 N·m
2
4
5
6
7
9
10
10
11
AD
2.5 ± 0.3 N·m
2.5 ± 0.3 N·m
1
4.9 ± 0.7 N·m
4.9 ± 0.7 N·m
8
Headlamp levelling switch
removal steps
•
Lower panel assembly (Refer to
GROUP 52A, Instrument Panel
Assembly ).
1.
Headlamp levelling switch
Headlamp removal steps
2.
Headlamp bulb (low-beam)
3.
Headlamp bulb (high-beam)
4.
Position lamp bulb socket
5.
Position lamp bulb
6.
Front turn-signal lamp bulb socket
7.
Front turn-signal lamp bulb
8.
Headlamp seal
Headlamp body removal step
•
Front bumper assembly (Refer to
GROUP 51, Front bumper
assembly ).
9.
Headlamp body
10. Grommet
11. Headlamp bracket
Headlamp removal steps
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст