Mitsubishi L200. Manual — part 752
MITSUBISHI MULTI COMMUNICATION SYSTEM (MMCS)
CHASSIS ELECTRICAL
54A-375
STEP 6. Temporarily replace the multivision
display, and check the trouble symptom.
After temporary replacement of the multivision dis-
play, check if the DVD image is displayed.
Q: Is the check result normal?
YES :
Replace the multivision display.
NO :
Replace the DVD.
Inspection Procedure 11: The picture and sound of external input are not played.
CAUTION
Whenever the multivision display is replaced, ensure that the power supply circuit and the earthing
circuit are normal. (Check that the voltage is 10 V or more.)
Audio and Video Adapter Communication Circuit
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Grey R : Red P : Pink V : Violet PU : Purple SI : Silver
MULTIVISION DISPLAY
AUDIO AND VIDEO ADAPTER
NOTE
: RHD
LHD
:
MITSUBISHI MULTI COMMUNICATION SYSTEM (MMCS)
CHASSIS ELECTRICAL
54A-376
COMMENTS ON TROUBLE SYMPTOM
The wiring harness between the audio and video
adapter and the multivision display, the audio and
video adapter or the multivision display may have a
problem.
NOTE: The connected equipment side or the con-
nection from the audio and video adapter to the
equipment may have a problem. Therefore, check
that the operation status and the connecting method
of the equipment connected to the multivision display
and audio and video adapter before performing the
diagnosis.
PROBABLE CAUSES
• The multivision display may be defective
• The audio and video adaptor may be defective
• Damaged harness wires and connectors
DIAGNOSIS
STEP 1. Check of DVD picture
Check that the DVD picture is displayed normally.
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Perform the troubleshooting related to the
MMCS (Refer to
).
STEP 2. Check the audio and video adapter.
Check the audio and video adapter.(Refer to
)
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Replace the audio and video adapter.
STEP 3. Connector check: C-167 multivision
display connector, D-40 audio and video adaptor
connector
Q: Is the check result normal?
YES :
Go to Step 4.
NO :
Repair the connector concerned.
AC903856AS
Connector: C-167 <LHD>
C-167 (GR)
Harness side
AC903865
Harness side
AJ
Connector: C-167 <RHD>
AC903885
Connector: D-40
AJ
Harness side
MITSUBISHI MULTI COMMUNICATION SYSTEM (MMCS)
CHASSIS ELECTRICAL
54A-377
STEP 4. Check the wiring harness between C-167
multivision display connector terminal No.37, 38,
39, 53, 54 and D-40 audio and video adaptor
connector terminal No. 1, 6, 5, 2, 4.
• Check the communication lines for open circuit
and short circuit.
NOTE:
Prior to the wiring harness inspection, check interme-
diate connectors C-15 and D-39, and repair if neces-
sary.
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Repair the wiring harness.
STEP 5. Temporarily replace the multivision
display, and check the trouble symptom.
Check that the external input is normal.
Q: Is the check result normal?
YES :
Replace the multivision display.
NO :
Replace the audio and video adapter.
MAIN UNIT TERMINAL VOLTAGE
M1546003300537
MULTIVISION DISPLAY
AC903856AS
Connector: C-167 <LHD>
C-167 (GR)
Harness side
AC903865
Harness side
AJ
Connector: C-167 <RHD>
AC901129AK
Connector: D-40
Harness side
AC903853
AT
Connector: C-15 <LHD>
AC903868
Connector: C-15 <RHD>
BO
AC611894AF
C-168
C-169
C-170
C-167
MITSUBISHI MULTI COMMUNICATION SYSTEM (MMCS)
CHASSIS ELECTRICAL
54A-378
C-168
C-167
C-169
C-170
Terminal
No.
Signal symbol
Check condition
Terminal voltage
71
ANTENNA POWER ON
Ignition switch: ACC position
System voltage (DC)
72
AMP POWER ON
Ignition switch: ACC position
1 V or less
Terminal
No.
Signal symbol
Check condition
Terminal voltage
37
VIDEO2-IN
When the image is input
1Vp-p (AC)
38
VIDEO2-R
When the sound is input
1.2Vrms (AC)
39
SEIELD (VIDEO2-L/R)
Always
1 V or less
43
AUDIO REMOTE
Ignition switch: ACC position
3.3V (DC)
53
SEIELD (VIDEO2-IN)
Always
Approximately 0 V
54
VIDEO2-L
When the sound is input
1.2Vrms (AC)
55
VIDEO2 DETECT
Always
1 V or less
59
SEIELD (STEERING REMO)
Always
1V or less
Terminal
No.
Signal symbol
Check condition
Terminal voltage
21
BATTERY (+)
Always
System voltage (DC)
24
PS-R
Sift lever <M/T> or selector
lever <A/T>: R position
Ignition switch: ON position
System voltage (DC)
Sift lever <M/T> or selector
lever <A/T>: Except R position
Ignition switch: ON position
1V or less
25
GND
Always
1V or less
Terminal
No.
Signal symbol
Check condition
Terminal voltage
2
SPEAKER RL (
−)
When the sound is output
0 - System voltage (AC)
3
SPEAKER FL (
−)
When the sound is output
0 - System voltage (AC)
7
SPEAKER FR (
−)
When the sound is output
0 - System voltage (AC)
8
SPEAKER RR (
−)
When the sound is output
0 - System voltage (AC)
9
MAIN GND
Always
1V or less
10
ILLUMINATION (+)
Tail lamp switch: ON
System voltage (DC)
11
SPEAKER RL (+)
When the sound is output
0 - System voltage (AC)
12
SPEAKER FL (+)
When the sound is output
0 - System voltage (AC)
13
VSS
Ignition switch: ON
• Running
0 - System voltage (pulse)
14
ACCESSORY (+)
Ignition switch: ACC position
System voltage (DC)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст