Mitsubishi L200. Manual — part 531
Door window glass assembly
removal steps
•
).
•
Beltline moulding, beltline
weatherstrip inner (Refer to
).
5.
Door window glass assembly
Door window regulator assembly
removal steps
>>
A
<<
•
Post-installation operation check
•
).
<<
B
>>
6.
Door window regulator assembly
7.
Power window motor <Vehicles
with power window>
AC509769
2
3
4
5
6
7
AD
<Vehicles with
power window>
<Vehicles without
power window>
<Rear door>
8
9
10
11
12
11
5.0 ± 1.0 N·m
5.0 ± 1.0 N·m
AC509770
1
11
7
AB
DOOR
BODY
42-184
Power window sub switch
<Vehicles with power window>
removal
1.
Power window sub switch (Refer to
GROUP 52A, Door Trim .)
Regulator handle <Vehicles with
manual window> removal steps
<<A>>
>>B<<
2.
Clip
>>B<<
3.
Regulator handle
>>B<<
4.
Escutcheon
Door window glass assembly
and stationary window glass
removal steps
•
Beltline moulding, beltline
weatherstrip inner (Refer to
.)
•
.)
5.
Door window glass assembly
6.
Door window glass holder
7.
Door window glass pad
•
Centre sash (Refer to
.)
8.
stationary window glass assembly
9.
stationary window weatherstrip
10. stationary window glass
Door window regulator assembly
removal steps
>>
A
<<
•
Post-installation operation check
•
.)
<<B>>
11. Door window regulator assembly
12. Power window motor <Vehicles
with power window>
DOOR
BODY
42-185
REMOVAL SERVICE POINTS
<<A>> CLIP REMOVAL
AC100005
Use a cloth to remove the clip as shown in the illus-
tration.
<<B>> DOOR WINDOW REGULATOR ASSEMBLY
REMOVAL
1. Remove the door window glass assembly
installation bolts.
AC100009AC
MB990480
CAUTION
If tinting film is adhered to the door window
glass, attach the special tool window glass
holder (MB990480) to the outside of the glass to
prevent the film from peeling off.
2. Lift the door window glass, and attach the special
tool window glass holder (MB990480) to the glass
as shown to prevent the glass from falling.
3. Remove the door window regulator assembly.
INSTALLATION SERVICE POINTS
>>A<< POST-INSTALLATION OPERATION
CHECK
When the following procedures are carried out, make
the power window switch learn the fully closed posi-
tion of the power window (Refer to
).
• Power window regulator removal or replacement
• Power window switch removal or replacement
>>B<< ESCUTCHEON/REGULATOR HANDLE/
CLIP INSTALLATION
AC100007AB
Front of vehicle
Horizontal line
30˚
1. Install the escutcheon and regulator handle to the
clip.
2. Close the door window glass fully, and then install
the regulator handle as shown in the illustration.
DOOR
BODY
42-186
INSPECTION
M1429001401241
POWER WINDOW MAIN SWITCH TERMI-
NAL CHECK
AC312988
1 2 3
4 5 6
7 8 9
12
10
13
11
14
E-03
AC
Termin
al No.
Check item
Check condition
Normal condition
1
Output to power window motor
−
−
2
Earth
Always
1 V or less
3
−
−
−
4
LIN communication line (ETACS-
ECU)
Always
0 to 12 V (pulse signal)
5
−
−
−
6
Power supply
Ignition switch: ON
System voltage
7
Output to power window motor
−
−
8
Input from power window motor
(pulse sensor earth)
−
0.5 V or less
9
Input from power window motor
(pulse sensor signal)
When the power windows are
operating
0 to 5 V (pulse signal)
10
Input from power window motor
(pulse sensor signal)
When the power windows are
operating
0 to 5 V (pulse signal)
11
−
−
−
12
Input from power window motor
(power supply to pulse sensor)
When the power windows are
operating
5 V
13, 14
−
−
−
POWER WINDOW SUB SWITCH TERMI-
NAL CHECK
AC312990
1
2 3
4 5 6 7 8
E-16: Front power window sub switch,
E-13: Rear power window sub switch (LH),
E-06: Rear power window sub switch (RH)
AC
Termin
al No.
Check item
Check condition
Normal condition
1
Earth
Always
1 V or less
2
Input from power window motor
(pulse sensor signal)
When the power windows are
operating
0 to 5 V (pulse signal)
3
Input from power window motor
(power supply to pulse sensor)
When the power windows are
operating
5 V
DOOR
BODY
42-187
DOOR HANDLE AND LATCH
REMOVAL AND INSTALLATION <SINGLE CAB>
M1423004601622
Pre-removal Operation
• Door Trim Assembly Removal (Refer to GROUP 52A,
Door Trim ).
Post-installation Operation
• Door Inside Handle Play Check (Refer to
• Door Outside Handle Play Check (Refer to
• Door Trim Assembly Installation (Refer to GROUP 52A,
Door Trim ).
AC808375
5.0 ± 1.0 N·m
5.0 ± 1.0 N·m
1
2
2
3
4
5
6
7
9
8
10
11
12
13
15
16
5.0 ± 1.0 N·m
5.0 ± 1.0 N·m
N
14
AE
31 ± 4 N·m
<Up to 2010 year
August>
24 ± 4 N·m
<From to 2010
year July>
4
Power supply
Ignition switch: ON
System voltage
5
Output to power window motor
−
−
6
LIN communication line (ETACS-
ECU)
Always
0 to 12 V (pulse signal)
7
Output to power window motor
−
−
8
Input from power window motor
(pulse sensor signal)
When the power windows are
operating
0 to 5 V (pulse signal)
Termin
al No.
Check item
Check condition
Normal condition
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст