Mitsubishi L200. Manual — part 446
TROUBLESHOOTING
ACTIVE STABILITY & TRACTION CONTROL SYSTEM (ASTC)
35C-40
Code No.C1211: Wheel speed sensor (RR) (signal short circuit)
ACB00772
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Grey R : Red P : Pink V : Violet PU : Purple
Wheel Speed Sensor Circuit
ASTC-ECU
FRONT WHEEL
SPEED SENSOR
(LH)
FRONT WHEEL
SPEED SENSOR
(RH)
REAR WHEEL
SPEED SENSOR
(LH)
REAR WHEEL
SPEED SENSOR
(RH)
AC800980
AG
Connector: A-48
(B)
AC600687CB
Connectors: C-29 <LHD>
16
10
13
4
1112
1 2 3
15
14
5
20
18
17
19
7
6
8 9
AC600635BE
Connector: C-29 <RHD>
16
10
13
4
1112
1 2 3
15
14
5
20
18
17
19
7
6
8 9
AC504324 AX
Connectors: F-10, F-12
F-10 (GR)
F-10 Harness connector
(harness side)
F-12 (B)
F-12
TROUBLESHOOTING
ACTIVE STABILITY & TRACTION CONTROL SYSTEM (ASTC)
35C-41
CAUTION
• If there is any problem in the CAN bus lines,
an incorrect diagnosis code may be set. Prior
to this diagnosis, diagnose the CAN bus lines
(Refer to GROUP 54C
− CAN Bus Diagnostics
Table .).
• Before replacing the ECU, ensure that the
communication circuit is normal.
OPERATION
• A toothed ABS rotor generates a voltage pulse as
it moves across the pickup field of each wheel
speed sensor.
• The wheel speed sensor transmit the frequency
of the pulses to the ASTC-ECU.
• The hydraulic unit assembly (integrated with
ASTC-ECU) modulates the amount of braking
force individually applied to each wheel cylinder.
DIAGNOSIS CODE SET CONDITION
Diagnosis code No.1211 is set if any abnormal volt-
age from the wheel speed sensor is detected without
the outputs of the codes No.C1210 or C1212.
PROBABLE CAUSES
Current trouble
• Damaged wiring harness and connectors
• Teeth lack or clogging of the ABS rotor
• Malfunction of the axle shaft bearing
• Noise interference
• Wheel speed sensor malfunction
• ASTC-ECU malfunction
Past trouble
• Carry out diagnosis with particular emphasis on
wiring harness and connector failures between
ASTC-ECU and the wheel speed sensor. For
diagnosis procedures, refer to How to treat past
trouble (GROUP 00
− How to Cope with Intermit-
tent Malfunctions .).
DIAGNOSIS PROCEDURE
STEP 1. M.U.T.-III CAN bus diagnosis
Use M.U.T.-III to diagnose the CAN bus lines.
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Repair the CAN bus lines (Refer to GROUP
54C
− CAN Bus Diagnostics Table .). On
completion, go to Step 2.
STEP 2. Diagnosis code recheck after resetting
CAN bus lines
(1) Erase the diagnosis code.
(2) Drive the vehicle at 15 km/h or more.
NOTE: The ABS warning lamp does not turn OFF
in some cases unless the vehicle runs at 15 km/h
or higher.
Q: Is the diagnosis code No.C1211 set?
YES :
Go to Step 3.
NO :
This diagnosis is complete.
STEP 3. M.U.T.-III diagnosis code
Check that the diagnosis codes No.C1210 or C1212
is also set.
Q: Are the diagnosis codes No.C1210 or C1212 also
set?
YES :
Perform the diagnosis for the diagnosis
codes No.C1210 (Refer to
).
NO :
Go to Step 4.
STEP 4. M.U.T.-III data list
Check the following data list (Refer to
• Item No.04: RR wheel speed sensor
Q: Is the check result normal?
YES :
Go to Step 12.
NO :
Go to Step 5.
TROUBLESHOOTING
ACTIVE STABILITY & TRACTION CONTROL SYSTEM (ASTC)
35C-42
STEP 5. Check for wheel speed sensor (RR)
installation
Check how the wheel speed sensor (RR) is installed
correctly (Disconnection of wheel speed sensor
(RR), loose mounting bolt, etc.).
Q: Is the check result normal?
YES :
Go to Step 6.
NO :
Reinstall the wheel speed sensor (RR)
correctly (Refer to
.). Then go to
Step 13.
STEP 6. Check for wheel speed sensor (RR)
output current
Refer to
Q: Is the check result normal?
YES :
Go to Step 7.
NO :
Replace the wheel speed sensor (RR)
(Refer to
.). Then go to Step 13.
STEP 7. Check the axle shaft bearing for
looseness.
NOTE:
.
•
If the wheel bearing or front hub or axle shaft
bearing are loose, the gap between the wheel
speed sensor and ABS rotor may become exces-
sive.
•
Check the axle shaft bearing, which diagnosis
code indicates, for looseness. (Refer to GROUP
27, On-vehicle service
−
Axle shaft axial play
check .).
Q: Is the check result normal?
YES :
Go to Step 8.
NO :
Replace the rear axle shaft bearing (Refer
to GROUP 27, Axle shaft assembly .). Then
go to Step 13.
STEP 8. Check the ABS rotor.
Check the ABS rotor (RR), which diagnosis code
indicates, for foreign material or deformation.
Q: Is the check result normal?
YES :
Go to Step 9.
NO :
If the ABS rotor (RR) is contaminated with
foreign material, clean it. If the rear axle
shaft bearing is deformed, replace it (Refer
to GROUP 27, Axle shaft assembly .). Then
go to Step 13.
STEP 9. Connector check: A-48 ASTC-ECU
connector, F-10 rear wheel speed sensor (RH), C-
29 intermediate connector and F-12 intermediate
connector
Q: Is the check result normal?
YES :
Go to Step 10.
NO :
Repair the defective connector. Then go to
Step 13.
STEP 10. Voltage measurement at the A-48
ASTC-ECU connector
(1) Disconnect the A-48 ASTC-ECU connector, the
F-10 rear wheel speed sensor (RH) connector.
(2) Measure the voltage between the A-48 ASTC-
ECU connector terminal No.21 and body earth.
OK: 1V or less
Q: Is the check result normal?
YES :
Go to Step 11.
NO :
Repair the harness wire. Then go to Step
13.
STEP 11. Resistance measurement at the A-48
ASTC-ECU connector
(1) Disconnect the F-10 rear wheel speed sensor
(RH) connector, and measure the resistance at
the harness connector side.
(2) Disconnect the A-48 ASTC-ECU connector.
(3) Measure the resistance between the A-48 ASTC-
ECU connector terminal No.21 and body earth.
OK: No continuity
Q: Is the check result normal?
YES :
Go to Step 12.
NO :
Repair the harness wire. Then go to Step
13.
STEP 12. Check whether the diagnosis code is
reset.
(1) Erase the diagnosis code.
(2) Drive the vehicle at 15 km/h or more.
NOTE: The ABS warning lamp does not turn OFF
in some cases unless the vehicle runs at 15 km/h
or higher.
Q: Is the diagnosis code No.C1211 set?
YES :
Replace the hydraulic unit (integrated with
ASTC-ECU) (Refer to
.). Then go
to Step 13.
NO :
Intermittent malfunction (Refer to GROUP
00
− How to Cope with Intermittent
Malfunctions .).
TROUBLESHOOTING
ACTIVE STABILITY & TRACTION CONTROL SYSTEM (ASTC)
35C-43
STEP 13. Check whether the diagnosis code is
reset.
(1) Erase the diagnosis code.
(2) Drive the vehicle at 15 km/h or more.
NOTE: The ABS warning lamp does not turn OFF
in some cases unless the vehicle runs at 15 km/h
or higher.
Q: Is the diagnosis code No.C1211 set?
YES :
Return to Step 1.
NO :
This diagnosis is complete.
Code No.C1216: Wheel speed sensor (RL) (signal short circuit)
ACB00772
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Grey R : Red P : Pink V : Violet PU : Purple
Wheel Speed Sensor Circuit
ASTC-ECU
FRONT WHEEL
SPEED SENSOR
(LH)
FRONT WHEEL
SPEED SENSOR
(RH)
REAR WHEEL
SPEED SENSOR
(LH)
REAR WHEEL
SPEED SENSOR
(RH)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст