Mitsubishi L200. Manual — part 647
POST-COLLISION DIAGNOSIS
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-259
3. Check the harness for binding, connectors for
damage, poor connections, and terminals for
deformation (Refer to
<SIDE AND CURTAIN AIR BAGS ARE
DEPLOYED>
1. Replace the following parts with new ones.
• SRS-ECU (Refer to
• Front seatback assembly (Refer to
• Curtain air bag module (Refer to
• Side impact sensor (Refer to
).
• Headlining (Refer to GROUP 52A, Headlining ).
• Front pillar trim, centre pillar upper trim, rear pillar
upper trim (Refer to GROUP 52A
− Interior Trim ).
• Seat belt with pre-tensioner (Refer to
).
2. Check the wiring harness for binding, the
connector for damage, and the terminal for
deformation (Refer to
WHEN AIR BAGS DO NOT DEPLOY IN LOW-
SPEED COLLISION.
Check the SRS components. If visible damage such
as dents, cracks, or deformation are found on the
SRS components, replace them with new ones. Con-
cerning parts removed for inspection, replacement
with new parts and cautions in working, refer to
FRONT IMPACT SENSOR
AC501622 AB
Front impact sensor
Radiator
1. Check the head lamp support panel for distortion
and rust.
2. Check the front impact sensor for dents, cracks,
deformation or rust.
3. Check the front impact sensor wiring harness for
binding, check the connector for damage, and
check the terminals for deformation.
NOTE: The figures show front impact sensors
(RH). The front impact sensors (LH) is symmetri-
cal with the front impact sensors (RH).
SRS-ECU
AC502256
SRS-ECU
AB
1. Check the SRS-ECU case for dents, cracks or
deformation.
2. Check the connector for damage, and the
terminals for deformation.
3. Check the SRS-ECU for installation condition.
AIR BAG MODULES
AC809499
Connector
Inflator case
Connector
Inflator case
Connector
Driver's air bag module
Passenger's (front) air bag module
<Vehicles without wide fender (optional)>
Connector
Inflator case
AC
<Vehicles with wide fender (optional)>
1. Check the pad cover for dents, cracks or
deformation.
POST-COLLISION DIAGNOSIS
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-260
2. Check the connector for damage, terminals
deformities, and the harness for binding.
3. Check the air bag inflator case for dents, cracks or
deformities.
4. Check the air bag modules for proper installation.
CLOCK SPRING
AC304044AC
Case
Protective tubes
1. Check the clock spring connectors and protective
tube for damage, and the terminals for
deformation.
2. Visually check the case for damage.
SEAT BELT PRE-TENSIONER
AC800971
Centre
pillar or
quarter pillar
AD
Seat belt
pre-tensioner
1. Check the seat belt for damage or deformation.
2. Check the seat belt pre-tensioner for cracks or
deformation.
3. Check that the unit is installed correctly to the
vehicle body.
FRONT SEAT ASSEMBLY (WITH BUILT-IN SIDE-
AIRBAG MODULE)
AC801114AB
Side-airbag
module
deployment
section
1. Check that the side-airbag module deployment
part of the seat is normal.
2. Check the connector for damage, the terminal for
deformation and the harness for binding.
SIDE IMPACT SENSOR
AC800518
AE
Side impact
sensor
Centre pillar
or quarter
pillar
1. Check the centre pillar <Double cab> or quarter
pillar <Club cab> for deformation.
2. Check the side impact sensor for dent, crack,
deformation or rust.
3. Check the connector for damage, the terminal for
deformation and the harness for binding.
NOTE: The illustration shows the side impact sensor
(LH). The position of the side impact sensor (RH) is
symmetrical to this.
CURTAIN AIR BAG MODULE
AC800743
Curtain air bag module
deployment section
AB
INDIVIDUAL COMPONENT SERVICE
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-261
1. Check that the curtain air bag deployment part of
the headlining is normal.
2. Check the inflator surface for cracks, dents or
deformations.
3. Check the connector for damage, the terminal for
deformation and the harness for binding.
NOTE: The illustration shows the curtain air bag
module (RH). The position of the curtain air bag
module (LH) is symmetrical to this.
STEERING WHEEL, STEERING COLUMN AND
SHAFT ASSEMBLY
1. Check the wiring harness (built into the steering
wheel) and the connectors for damage, and the
terminals for deformation.
2. Install the air bag module to check fit or alignment
with the steering wheel.
3. Check the steering wheel for noise, binding or
difficult operation and excessive free play.
4. Check the steering column shaft shock absorbing
mechanism (Refer to GROUP 37, On-vehicle
Service ).
HARNESS CONNECTOR (INSTRUMENT PANEL
WIRING HARNESS AND FLOOR WIRING
HARNESS)
Check harnesses for binding, connectors for damage
and terminals for deformation (Refer to
).
INDIVIDUAL COMPONENT SERVICE
M1524002901069
WARNING
•
If heat damage may occur during paint work, remove the SRS-ECU, the air bag modules,
the clock spring, impact sensors, passenger’s air bag cut off switch and the seat belt with
pre-tensioner.
•
SRS-ECU, air bag modules, clock spring, impact sensors and passenger’s air bag cut
off switch: 93
°
C or more
•
Seat belt with pre-tensioner: 90
°
C or more
•
If the SRS components are removed for the purpose of check, sheet metal repair, painting,
etc., they should be stored in a clean, dry place until they are reinstalled.
If the SRS components are to be removed or
replaced as a result of maintenance, troubleshooting
etc., follow the service procedures that follow.
• Front impact sensors; refer to
• SRS-ECU; refer to
• Driver’s and passenger’s (front) air bag modules
and clock spring; refer to
• Side-air bag module; refer to
• Curtain air bag module; refer to
• Side impact sensors; refer to
• Seat belt with pre-tensioner; refer to
WARNING/CAUTION LABELS
M1524003002039
Caution labels on the SRS are attached in the vehicle as shown. Follow label instructions when servicing the
SRS. If the label(s) are dirty or damaged, replace with new one(s).
AC501619
AC501620
AC501671
AC800660
AC800659
AC900542
AC800593
Passenger's (front)
air bag module
SRS-ECU
Sunvisor
Instrument panel
Curtain air bag module
(right and left)
Side-airbag module
(right and left)
Glove box
Passenger's air bag
cut off switch
Seat belt pre-tensioner
(driver's and front passenger's seat)
Passenger's air bag
cut off switch
AD
Driver's air bag module
<Vehicles without wide fender
(optional)>
<Vehicles with wide fender
(optional)>
(Passenger side)
WARNING/CAUTION LABELS
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-262
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст