Mitsubishi L200. Manual — part 679
COMBINATION METER
CHASSIS ELECTRICAL
54A-83
STEP 2. Check the diagnosis code of the engine-
ECU.
Check if the diagnosis code is set in either of the
engine-ECU.
Q: Is the diagnosis code set?
YES :
Diagnose the engine-ECU (Refer to
GROUP 13A
− Troubleshooting . On
completion, go to Step 4.
NO :
Go to Step 3.
STEP 3. M.U.T.-III data list
Check the input signals below, which are related to
the seat belt warning lamp function.
• Turn the ignition switch to the "ON" position.
• Remove the each inserted seatbelt.
OK: Normal conditions are displayed for all
the items.
Q: Is the check result normal?
YES <All the signals are received normally.> :
Go
to Step 4.
NO <The seat belt switch signal is not received.> :
Refer to inspection procedure C-6 "The seat
belt switch signal is not received
<L.H. drive vehicles> or
<R.H.
drive vehicles>."
NO <The ignition switch (IG1) signal is not
received.> :
Refer to inspection procedure C-3
"The ignition switch (IG1) signal is not
received
."
STEP 4. Check the combination meter
Q: Does the combination meter work?
YES :
Go to Step 5.
NO :
Refer to symptom procedure 1 "Power
supply circuit system check
STEP 5. Connector check: C-113 combination
meter connector and C-219 ETACS-ECU
connector
Q: Is the check result normal?
YES :
Go to Step 6.
NO :
Repair the defective connector.
Item
No.
Item name
Normal condition
30
Ignition switch(IG1)
ON
50
Driver’s
seatbelt(Buckle SW)
Being turned ON
from OFF
51
Passenger
seatbelt(Buckle SW)
AC903856
Harness side
BH
Connector: C-113 <LHD>
AC903868
Harness side
BY
Connector: C-113 <RHD>
AC509934
Connector: C-219 <LHD>
AD
C-219 (GR)
Harness side
Junction block
AC509943
Connector: C-219 <RHD>
AB
C-219 (GR)
Harness side
Junction block
(Rear view)
COMBINATION METER
CHASSIS ELECTRICAL
54A-84
STEP 6. Check the wiring harness from C-113
combination meter connector terminal No.9 to C-
219 ETACS-ECU connector terminal No.73.
• Check the output lines for open circuit.
Q: Is the check result normal?
YES :
Go to Step 7.
NO :
Repair the wiring harness.
STEP 7. Retest the system.
The door-ajar warning lamp function should work
normally.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
use Troubleshooting/inspection Service
Points
− How to Cope with Intermittent
Malfunction ).
NO :
Replace the ETACS-ECU and register the
ID codes (Refer to
AC903856
Harness side
BH
Connector: C-113 <LHD>
AC903868
Harness side
BY
Connector: C-113 <RHD>
AC509934
Connector: C-219 <LHD>
AD
C-219 (GR)
Harness side
Junction block
AC509943
Connector: C-219 <RHD>
AB
C-219 (GR)
Harness side
Junction block
(Rear view)
COMBINATION METER
CHASSIS ELECTRICAL
54A-85
CHECK AT ECU TERMINALS
M1540201200488
Connector: C-111
Terminal
No.
Check item
Check condition
Normal condition
51
Glow indicator lamp
Ignition switch: ON and glow
indicator lamp: OFF
System voltage
52
Charge warning lamp
Ignition switch: ON and before
alternator generation and charge
warning lamp: OFF
System voltage
53
− 55
−
−
−
56
Input of turn-signal lamp LH switch Ignition switch: ON and turn-
signal lamp (LH) switch: ON and
turn-signal lamp: ON (turn: ON)
System voltage
57
Earth
Always
1 V or less
58
−
−
−
59
Over drive off indicator
Ignition switch: ON and over drive
off switch: ON and over drive off
indicator: ON
System voltage
60
A/T fluid temperature warning lamp Ignition switch: ON and A/T fluid
temperature warning lamp: OFF
System voltage
61
Oil pressure switch
Ignition switch: ON and before
starting the engine and oil
pressure warning lamp: OFF
System voltage
62
−
−
−
63
Check engine warning lamp
Ignition switch: ON and check
engine warning lamp: OFF
System voltage
64
Water separator indicator lamp
Ignition switch: ON and water
level switch: ON and water
separator indicator lamp: ON
1 V or less
AC502672AF
C-111
C-112
C-113
COMBINATION METER
CHASSIS ELECTRICAL
54A-86
Connector: C-112
Connector: C-113
Terminal
No.
Check items
Check conditions
Normal conditions
31
Shift indicator
− L
Ignition switch: ON and shift lever
is in L position
System voltage
32
TCL OFF indicator lamp
Ignition switch: ON and TCL OFF
indicator lamp: ON
System voltage
33
ASC warning lamp
Ignition switch: ON and ASC
warning lamp: ON
System voltage
34
Tachometer (engine speed)
Engine: Started
Pulse signal
35
Speedometer (vehicle speed)
Running
Pulse signal
36
Power supply from ignition switch
(IG1)
Ignition switch: ON
System voltage
37
Shift indicator
− 2
Ignition switch: ON and shift lever
is in 2 position
System voltage
38
Shift indicator
− D
Ignition switch: ON and shift lever
is in D position
System voltage
39
Shift indicator
− N
Ignition switch: ON and shift lever
is in N position
System voltage
40
Shift indicator
− R
Ignition switch: ON and shift lever
is in R position
System voltage
41
Shift indicator
− P
Ignition switch: ON and shift lever
is in P position
System voltage
42
Battery power supply
Always
System voltage
Terminal
No.
Check items
Check conditions
Normal conditions
1
−
−
−
2
Door ajar warning lamp
Ignition switch: ON and door is
open and door ajar warning lamp:
ON
1 V or less
3
− 7
−
−
−
8
4WD indicator lamp
Ignition switch: ON and 4WD
indicator lamp: OFF
System voltage
9
Seat belt warning lamp
Ignition switch: ON and seat belt
switch: ON
System voltage
10, 11
−
−
−
12
Input of parking brake switch and
brake fluid level switch
• Ignition switch: ON and parking
brake switch: ON
• Ignition switch: ON and brake
fluid level switch: ON
• Ignition switch: ON and
vacuum switch: ON
• Brake warning lamp: ON
1 V or less
13
Earth
Always
1 V or less
14
−
−
−
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст