Mitsubishi L200. Manual — part 200

ON-VEHICLE SERVICE

DIESEL FUEL

13A-596

THROTTLE VALVE CONTROL SERVO
CHECK

M1133010700283

OPERATION CHECK

1. Remove the air intake hose from the throttle body.
2. Turn the ignition switch to "ON" position.
3. Make sure that the throttle valve is open.
4. Turn the ignition switch to "OFF" position.

CHECK THE COIL RESISTANCE

1. Disconnect the electronic - controlled throttle

valve connector.

2. Measure resistance between terminal No. 5 and

No. 6 at the throttle valve control servo connector.

Standard value: 0.3

− 100 Ω (at 20 °C)

3. If resistance is outside the standard value, replace

the throttle body assembly.

AK501458

6

1 2 3 4 5

AB

Equipment side
connector

Electronic-controlled
throttle valve
(incorporating throttle
position sensor)

FUEL INJECTOR

DIESEL FUEL

13A-597

FUEL INJECTOR

REMOVAL AND INSTALLATION

M1133009400299

<Except Euro5>

Pre-removal Operation
• Inlet Manifold Removal (Refer to GROUP 15 − Inlet Mani-

fold ).

• Fuel Injection Pipe Removal (Refer to

P.13A-604

).

Post-installation Operation
• Fuel Injection Pipe Installation (Refer to

P.13A-604

).

• Inlet Manifold Installation (Refer to GROUP 15 − Inlet

Manifold ).

AC502869AE

1

17

16

15

14

10

11

11

10

6

13

N

3

10 ± 2 N·m

10 ± 2 N·m

15 ± 2 N·m

12

15 ± 2 N·m

7

N

9

N

3.0 ± 1.0 N·m to

10 ± 2 N·m

5

N

18

N

4

N

10 ± 1 N·m to

+120˚ – +125˚

8

N

13

N

(Engine oil)

2

FUEL INJECTOR

DIESEL FUEL

13A-598

Removal steps

•

When the fuel injector is replaced,
register the injector identification
code and perform the fuel injection
learning (Refer to GROUP 00

−

Precautions before Service, What
the Common Rail Engine Learns )
<Installation only>.

1.

Breather hose connection

2.

Harness bracket

3.

Timing belt front upper cover

>>

D

<< 4.

Oil seal

>>

D

<< 5.

Oil seal

<<

A

>> >>

C

<< 6.

Rocker cover assembly

7.

Rocker cover gasket A

8.

Rocker cover gasket B

9.

Rocker cover gasket C

>>

B

<< 10. Semi-circular packing

>>

A

<< 11. Eye bolt

>>

A

<< 12. Fuel leakage pipe

>>

A

<< 13. Fuel leak-off gasket

>>

A

<< 14. Injector holder bolt

>>

A

<< 15. Injector supporter

>>

A

<< 16. Pivot boss

>>

A

<< 17. Fuel injector

>>

A

<< 18. Nozzle gasket

Removal steps (Continued)

FUEL INJECTOR

DIESEL FUEL

13A-599

<Euro5>

AC805674 AD

1

19

18

17

16

12

13

13

12

8

15

N

4

10 ± 2 N·m

10 ± 2 N·m

15 ± 2 N·m

14

15 ± 2 N·m

9

N

11

N

3.0 ± 1.0 N·m to

10 ± 2 N·m

6

N

20

N

5

N

10 ± 1 N·m to

+120˚ – +125˚

10

N

15

N

(Engine oil)

2

3

7

23 ± 6 N·m

Removal steps

•

When the fuel injector is replaced,
register the injector identification
code and perform the fuel injection
learning (Refer to GROUP 00

−

Precautions before Service, What
the Common Rail Engine Learns )
<Installation only>.

1.

Breather hose connection

2.

Harness bracket

3.

Solenoid valve and harness
bracket assembly

4.

Timing belt front upper cover

>>

D

<< 5.

Oil seal

>>

D

<< 6.

Oil seal

7.

Vacuum pipe and hose assembly
connection

<<

A

>> >>

C

<< 8.

Rocker cover assembly

9.

Rocker cover gasket A

10. Rocker cover gasket B
11. Rocker cover gasket C

>>

B

<< 12. Semi-circular packing

>>

A

<< 13. Eye bolt

>>

A

<< 14. Fuel leakage pipe

>>

A

<< 15. Fuel leak-off gasket

>>

A

<< 16. Injector holder bolt

>>

A

<< 17. Injector supporter

Removal steps (Continued)