Mitsubishi L200. Manual — part 594
TROUBLESHOOTING
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-47
PROBABLE CAUSES
• Damaged harness wires and connectors
• Short to the power supply in the passenger's
(front) air bag module (squib) harness
• Malfunction of the passenger’s air bag cut off
switch
• Malfunction of the SRS-ECU
DIAGNOSIS PROCEDURE
STEP 1. Check the passenger’s air bag cut off
switch.
Check the passenger's air bag cut off switch (Refer
to
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Replace passenger’s air bag cut off switch
(Refer to
).
STEP2. Check the diagnosis code by connecting
a dummy resistor. (M.U.T.-III diagnosis code)
(1) Disconnect the negative battery terminal.
AC509788
C-02 (R)
AC
Glove box striker
2 1
Harness side
connector
(front view)
Lock
lever
Connector: C-02
(2) Disconnect passenger’s (front) air bag module
connector C-02. Pull up the harness side lock
lever with a nail and disconnect the connector
lock.
AC300956 AP
MB991865
(Dummy resistor: 3 )
MB991866
(Resistor harness)
C-02 Passenger's
(front) air bag
module connector
C-02 Harness side
connector
(3) Connect special tool dummy resistor (MB991865)
to special tool resistor harness (MB991866).
CAUTION
Do not insert a test probe into the terminal from
its front side directly as the connector contact
pressure may be weakened.
(4) Insert special tool (MB991866) into the harness
side connector C-02 by backprobing.
(5) Check that the passenger's air bag cut off switch
is "ON" position.
(6) Connect the negative battery terminal.
(7) Erase the diagnosis code memory, and check the
diagnosis code.
Q: Is diagnosis code B1413 set?
YES :
Go to Step 3.
NO :
Replace the passenger's (front) air bag
module (Refer to
STEP 3. Voltage measurement at the SRS-ECU
connector C-131.
(1) Disconnect the negative battery terminal.
AC501670
AB
C-131 (Y)
Connector: C-131
Harness side
connector
(rear view)
(2) Disconnect SRS-ECU connector C-131.
AC509788
C-02 (R)
AC
Glove box striker
2 1
Harness side
connector
(front view)
Lock
lever
Connector: C-02
DANGER
To prevents the air bag from deploying unin-
tentionally, disconnect the passenger’s
(front) air bag module connector C-02 to
short the squib circuit.
(3) Disconnect passenger’s (front) air bag module
connector C-02. Pull up the harness side lock
lever with a nail and disconnect the connector
TROUBLESHOOTING
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-48
lock.
AC006036
Section
A - A
C-131Harness side connectors
(front view)
Cable tie
Short spring
4 mm or more
Terminal
BC
A
A
CAUTION
Insert an insulator such as a cable tie to a depth
of 4 mm or more, otherwise the short spring will
not be released.
(4) Insert a cable tie [3 mm wide, 0.5 mm thick]
between terminals 9, 10 and the short spring to
release the short spring.
(5) Check that the passenger's air bag cut off switch
is "ON" position.
(6) Connect the negative battery terminal.
(7) Turn the ignition switch to the "ON" position.
13 14 15 16 17 18 19 20
5 6 7 8 9 10 11 12
1 2
3 4
AC006257AV
C-131 Harness side
connector (rear view)
CAUTION
Do not insert a test probe into the terminal from
its front side directly as the connector contact
pressure may be weakened.
(8) Voltage measurement between C-131 harness
side connector terminals 9, 10 and body earth.
OK: 1 V or less
Q: Is the check result normal?
YES :
Go to Step 4.
NO :
Repair the harness wires between SRS-
ECU connector C-131 (terminal No.9 and
10) and passenger's (front) air bag module
connector C-02 (terminal No.1 and 2).
STEP 4. Check whether the diagnosis code is
reset.
Q: Is diagnosis code B1413 set?
YES :
).
NO :
An intermittent malfunction is suspected
(Refer to GROUP 00, How to Cope with
Intermittent Malfunction ).
TROUBLESHOOTING
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-49
Code No.B1476: Power supply voltage (IG1 (A) voltage) drops abnormally.
IG1 Power Supply Circuit System
IGNITION
SWITCH (IG1)
SRS-ECU
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Grey R : Red P : Pink V : Violet PU : Purple
OPERATION
• The SRS-ECU is powered from the ignition
switch (IG1).
• The SRS-ECU power is supplied from two cir-
cuits. Even if one circuit is shut off, the air bag
can inflate.
DIAGNOSIS CODE SET CONDITIONS
This diagnosis code is set if the voltage between the
IG1 terminals (fuse No.15 circuit) and earth is lower
than a predetermined value for a continuous period
of 5 seconds or more.
PROBABLE CAUSES
• Damaged wiring harnesses or connectors
• Malfunction of the SRS-ECU
TROUBLESHOOTING
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-50
DIAGNOSIS PROCEDURE
STEP 1. Check junction block fuse number 15.
AC509744
AD
Fuse No.15
Junction
block
<LHD>
AD
AC502795
AC
Fuse No.15
Junction
block
<RHD>
Q: Is the fuse burned out?
YES :
Go to Step 4.
NO :
Go to Step 2.
STEP 2. Voltage measurement at the SRS-ECU
connector C-131.
(1) Disconnect the negative battery terminal.
AC501670
AB
C-131 (Y)
Connector: C-131
Harness side
connector
(rear view)
(2) Disconnect SRS-ECU connector C-131.
(3) Connect the negative battery terminal.
(4) Turn the ignition switch to the "ON" position.
13 14 15 16 17 18 19 20
5 6 7 8 9 10 11 12
1 2
3 4
AC203786
C-131 Harness side connector
(rear view)
AI
CAUTION
Do not insert a test probe into the terminal from
its front side directly as the connector contact
pressure may be weakened.
(5) Voltage measurement between C-131 harness
side connector terminal 16 and body earth.
OK: 9 V or more.
Q: Is the check result normal?
YES :
Go to Step 6.
NO :
Go to Step 3.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст