Mitsubishi Lancer (4A9 engine). Manual — part 245
GENERAL INFORMATION
CONTROLLER AREA NETWORK (CAN)
54C-4
NOTE:
.
•
Dominant ECU: ETACS-ECU and engine
ECU
•
Non-dominant ECU: ECU and sensor on
CAN-C network, excluding ETACS-ECU and
engine ECU
• To the CAN bus line, ECU, sensor, and diagnosis
connector are connected as follows for each net-
work.
CAN-B
• WCM <vehicles without KOS> or KOS-ECU
<vehicles with KOS>
• SRS-ECU
• Heater control unit <vehicles without A/C>
• A/C-ECU <vehicles with A/C>
• Radio and CD player <vehicles with Radio
and CD player> or CAN box unit <vehicles
with MMCS (vehicles for Russia)>
• Combination meter
CAN-C
• Headlamp automatic levelling-ECU <vehicles
with AFS>
• Steering wheel sensor <vehicles with ASC or
AFS>
• AS&G-ECU <vehicles with automatic stop &
go (AS&G) system>
• ABS-ECU <vehicles without ASC> or ASC-
ECU <vehicles with ASC>
• A/T-ECU <A/T> or CVT-ECU <CVT>
• Electric power steering-ECU <vehicles with
Electric power steering>
• Engine-ECU
• Corner sensor/back sensor-ECU <vehicles
with reversing sensor system>
Diagnosis CAN-C
• Diagnosis connector
SPECIAL TOOLS
CONTROLLER AREA NETWORK (CAN)
54C-5
SPECIAL TOOLS
M1548304200972
SPECIAL TOOLS
CONTROLLER AREA NETWORK (CAN)
54C-6
Tool
Number
Name
Use
MB991910
MB991826
MB991955
MB991911
MB991824
MB991827
MB991825
a
b
c
d
e
f
DO NOT USE
MB991955
a. MB991824
b. MB991827
c. MB991910
d. MB991911
e. MB991825
f. MB991826
M.U.T.-III sub-
assembly
a. Vehicle
Communicati
on Interface
(V.C.I.)
b. M.U.T.-III
USB cable
c. M.U.T.-III
main harness
A (Vehicles
with CAN
communicatio
n system)
d. M.U.T.-III
main harness
B (Vehicles
without CAN
communicatio
n system)
e. M.U.T.-III
measure
adapter
f. M.U.T.-III
trigger
harness
CAUTION
For vehicles with CAN
communication, use M.U.T.-III
main harness A to send
simulated vehicle speed. If you
connect M.U.T.-III main harness B
instead, the CAN communication
does not function correctly.
CAN bus diagnostics
MB991223
a
d
c
b
DO NOT USE
BA
MB991223
a. MB991219
b. MB991220
c. MB991221
d. MB991222
Harness set
a. Check
harness
b. LED harness
c. LED harness
adapter
d. Probe
Continuity check and voltage
measurement at harness wire or
connector
a. For checking connector pin
contact pressure
b. For checking power supply
circuit
c. For checking power supply
circuit
d. For connecting a locally sourced
tester
MB992006
TEST EQUIPMENT
CONTROLLER AREA NETWORK (CAN)
54C-7
TEST EQUIPMENT
M1548304300333
Test equipment
Name
Use
AC000019
Digital multimeter
Checking CAN bus circuit (for resistance and voltage
measurements)
MB992006
Extra fine probe
Continuity check and voltage
measurement at harness wire or
connector
MB992110
MB992110
Power plant ECU
check harness
Checking continuity and measuring
voltage at engine-ECU <Petrol>
harness-side connector
MB992044
MB992044
Power plant ECU
check harness
Checking continuity and measuring
voltage at engine-ECU <Diesel>
harness-side connector
B991974
MB991974
ABS check
harness
Checking continuity and measuring
voltage at ABS-ECU harness-side
connector
MB991997
MB991997
ASC check
harness
Checking continuity and measuring
voltage at ASC-ECU harness-side
connector
Tool
Number
Name
Use
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст