Mitsubishi Lancer (4A9 engine). Manual — part 21

SUPPORT LOCATIONS FOR LIFTING AND JACKING

GENERAL

00-81

SUPPORT LOCATIONS FOR LIFTING AND JACKING

M1001000700985

SUPPORT POSITIONS FOR A GARAGE JACK

CAUTION

Be sure to support the specified locations only. Otherwise, deformation of vehicle may occur.

AC801797

<Front side>

<Rear side>

Centremember

AB

Suspension
crossmember

SUPPORT LOCATIONS FOR LIFTING AND JACKING

GENERAL

00-82

SUPPORT POSITIONS FOR RIGID RACKS AND SINGLE-POST LIFT OR DOUBLE-
POST LIFT

CAUTION

• If rubber attachments with grooves that are too thick are used at the front support positions, the

front fender may become bent, so be sure to use rubber attachments with groove thicknesses of
18 mm or less.

• If attachments which are not high enough are used, they may damage areas such as the side step.

Be sure to use attachments which are high enough, or remove the side step if not using attach-
ments.

AC700197AB

Notch

Notch

Rubber

Rubber

Rigid racks

Notch

Notch

Single-post lift or
double-post lift

SUPPORT LOCATIONS FOR LIFTING AND JACKING

GENERAL

00-83

SUPPORT POSITIONS FOR PLATE TYPE
LIFT

CAUTION

Insert a spacer between the notch and the lift to
avoid damage to the side sill garnish. Be careful
not to contact the spacer against the side sill.
Support the notch with a spacer (100-mm width, 100-
mm height and 200-mm depth).

11A-1

GROUP 11A

ENGINE

MECHANICAL

<4A9>

CONTENTS

GENERAL INFORMATION . . . . . . . .

11A-2

SERVICE SPECIFICATIONS. . . . . . .

11A-2

SEALANTS AND ADHESIVES . . . . .

11A-3

SPECIAL TOOLS. . . . . . . . . . . . . . . .

11A-4

ON-VEHICLE SERVICE. . . . . . . . . . .

11A-7

DRIVE BELT TENSION CHECK AND ADJUSTMENT

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11A-7

POWER STEERING OIL PUMP DRIVE BELT CHECK
<Euro4> . . . . . . . . . . . . . . . . . . . . . . . . . . .

11A-11

IGNITION TIMING CHECK . . . . . . . . . . . . .

11A-12

IDLE SPEED CHECK . . . . . . . . . . . . . . . . .

11A-13

IDLE MIXTURE CHECK . . . . . . . . . . . . . . .

11A-14

VALVE CLEARANCE CHECK AND ADJUSTMENT

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11A-14

COMPRESSION PRESSURE CHECK. . . .

11A-16

MANIFOLD VACUUM CHECK . . . . . . . . . .

11A-17

CRANKSHAFT PULLEY . . . . . . . . . .

11A-18

CRANKSHAFT PULLEY REMOVAL AND
INSTALLATION. . . . . . . . . . . . . . . . . . . . . .

11A-18

CAMSHAFT . . . . . . . . . . . . . . . . . . . .

11A-24

CAMSHAFT REMOVAL AND INSTALLATION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11A-24

VALVE STEM SEAL . . . . . . . . . . . . . .

11A-31

VALVE STEM SEAL REMOVAL AND INSTALLATION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11A-31

OIL PAN . . . . . . . . . . . . . . . . . . . . . . .

11A-37

OIL PAN REMOVAL AND INSTALLATION.

11A-37

OIL PAN INSPECTION . . . . . . . . . . . . . . . .

11A-38

CRANKSHAFT OIL SEAL . . . . . . . . .

11A-39

CRANKSHAFT OIL SEAL REMOVAL AND
INSTALLATION . . . . . . . . . . . . . . . . . . . . . .

11A-39

CYLINDER HEAD GASKET . . . . . . . .

11A-42

CYLINDER HEAD GASKET REMOVAL AND
INSTALLATION . . . . . . . . . . . . . . . . . . . . . .

11A-42

TIMING CHAIN . . . . . . . . . . . . . . . . . .

11A-49

TIMING CHAIN REMOVAL AND INSTALLATION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11A-49

ENGINE ASSEMBLY . . . . . . . . . . . . .

11A-56

ENGINE ASSEMBLY REMOVAL AND INSTALLATION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11A-56