Mitsubishi Lancer (4A9 engine). Manual — part 118
HEADLAMP
CHASSIS ELECTRICAL
54A-134
Comfort flasher With/without
comfort flasher
function
Disable
No function
Enable
With function (initial condition)
Comfort flasher
switch time
Switch operation
time to activate the
comfort flasher
function
Normal
0.4 second (initial condition)
Long
0.8 second
Hazard answer
back
Adjustment of the
number of keyless
hazard warning
lamp answer back
flashes
Lock:1, Unlock:2
LOCK: Flashes once, UNLOCK: Flashes
twice (initial condition)
Lock:1, Unlock:0
LOCK: Flashes once, UNLOCK: No flash
Lock:0, Unlock:2
LOCK: No flash, UNLOCK: Flash twice
Lock:2, Unlock:1
LOCK: Flash twice, UNLOCK: Flash once
Lock:2, Unlock:0
LOCK: Flash twice, UNLOCK: No flash
Lock:0, Unlock:1
LOCK: No flash, UNLOCK: Flash once
Lock:0, Unlock:0
No function
Sensitivity for
auto lamp
Lighting control
sensor sensitivity
(illumination
intensity) <vehicles
with auto lamp>
Level 1 bright
High-high ambient brightness
Level 2 bright
High ambient brightness
Level 3
Standard ambient brightness (initial
condition)
Level 4 dark
Low ambient brightness
Level 5 dark
Low-low ambient brightness
Head lamp auto
cut customise
Adjustment of
headlamp
automatic shutdown
function
Disable
No function
Enable (B-spec.)
With function (initial condition)
Coming home
light
Disabling or
enabling coming
home light function
Disabled
No function
15 sec
The headlamps illuminate for 15 seconds.
30sec
The headlamps illuminate for 30 seconds.
(initial condition)
60 sec
The headlamps illuminate for 60 seconds.
180 sec
The headlamps illuminate for 180 seconds.
Welcome light
Disabling or
enabling welcome
light function
Disabled
No function <Initial condition (vehicles for
RUSSIA)>
Small
The tail lamp illuminates. <Initial condition
(except vehicles for RUSSIA)>
Head
The headlamps illuminate.
Adjustment
item (M.U.T.-III
display)
Adjustment item
Adjusting content
(M.U.T.-III display)
Adjusting content
HEADLAMP
CHASSIS ELECTRICAL
54A-135
HEADLAMP REMOVAL AND INSTALLATION
M1540101000506
REMOVAL SERVICE POINTS
<<A>> HEADLAMP CONTROL UNIT (HARNESS)
REMOVAL <VEHICLES WITH DISCHARGE HEAD-
LAMP>
1. As shown in the figure, use the commercial tool to
remove it.
Post-installation operation
Check the beam direction of the headlamp (Refer to
Headlamp Aiming ).
AC613544AB
8
4.5 ± 1.5 N·m
9
1
2
3
4
5
6
7
3
4.5 ± 1.5 N·m
4.5 ± 1.5 N·m
1.5 ± 0.3 N·m
Grommet
Section A - A
1
A
A
Removal Steps
•
Front bumper and radiator grille
assembly (Refer to GROUP 51 -
Front Bumper Assembly and
Radiator Grille ).
1.
Headlamp assembly
2.
Headlamp bulb socket cover
<Vehicles with discharge
headlamp>
<<
A
>> >>
A
<<
3.
Headlamp control unit <Vehicles
with discharge headlamp>
<<
B
>>
4.
Headlamp bulb <Vehicles with
discharge headlamp>
5.
Headlamp bulb (low-beam)
<Vehicles without discharge
headlamp>
6.
Headlamp bulb (high-beam)
<Vehicles without discharge
headlamp> or bending lamp
<Vehicles with discharge
headlamp>
7.
Front turn-signal lamp bulb
8.
Position lamp bulb
9.
Grommet
AC712425AC
Commercial tool
HEADLAMP
CHASSIS ELECTRICAL
54A-136
2. To insert the tool available in the market into the
headlamp assembly from the opening at the
igniter side, firstly remove the headlamp control
unit, the socket cover, the igniter and the earth
connector.
3. Using the commercial tool, make the resin washer
sag to push up the harness above the resin
washer.
4. Pull out the harness from the headlamp assembly.
<<B>> HEADLAMP BULB REMOVAL <VEHICLES
WITH DISCHARGE HEADLAMP>
CAUTION
Do not touch the bulb surface with bare hands or
dirty gloves. If the bulb surface (glass part) gets
dirty, immediately clean it with alcohol or thinner.
After drying completely, install the bulb.
1. Twist the socket cover to remove.
2. Disconnect the igniter.
3. Release the bulb securing spring, and remove the
bulb.
AC712430AC
Igniter
Earth
connector
Headlamp
control unit
connector
Commercial
tool
AC802237AB
Resin washer
Commercial tool
Headlamp control unit connector
Harness
Resin washer
Rib
AC613475
AB
Socket cover
AC609658
ZC501539
AC701335
AB
Igniter
AC609659
AC701336
AB
Spring
HEADLAMP
CHASSIS ELECTRICAL
54A-137
INSTALLATION SERVICE POINT
>>A<< HEADLAMP CONTROL UNIT INSTALLA-
TION <VEHICLES WITH DISCHARGE HEAD-
LAMP>
1. As shown in the figure, doubly wrap the portion in
the vinyl tape, from the headlamp control unit
connector root to the point where the harness
separation is hidden.
2. Install the harness to the headlamp assembly. At
that time, fitting the harness into the resin washer
is unnecessary.
HEADLAMP LEVELLING SWITCH REMOVAL AND INSTALLATION
M1540105200148
AC712428AC
Plastic tape
Headlamp control
unit connector
AC712429
AC709853
AB
1
2
Removal Steps
1.
Instrument lower panel (Refer to
GROUP 52A
− Instrument Lower
Panel ).
2.
Headlamp levelling switch
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст