Mitsubishi Lancer (4A9 engine). Manual — part 88
BATTERY
CHASSIS ELECTRICAL
54A-14
REMOVAL AND INSTALLATION
M1541001301506
<1600, 1800-PETROL, 2000>
CAUTION
If the battery current sensor or engine-ECU is replaced, make the battery current sensor learn the
zero point. (Refer to GROUP 00, Precautions Before Service
− Battery Current Sensor Calibration.)
<Low CO
2
specification, FFV>
ACB01849
AB
2
5
6
7
4
9
12
11
8.5 ± 1.5 N·m
12 ± 2 N·m
4.0 ± 1.0 N·m
5.0 ± 1.0 N·m
6.0 ± 2.0 N·m
10
8
1
2
3
5.0 ± 1.0 N·m
<Low CO2 specification, FFV>
<Except Low CO2
specification, FFV>
12 ± 2 N·m
Removal steps
1.
Battery current sensor <Low CO
2
specification, FFV>
2.
Connection of the battery harness
[negative battery terminal]
3.
Battery terminal assembly [negative
battery terminal] <Low CO
2
specification, FFV>
•
Air cleaner intake duct (Refer to GROUP
15
− Air Cleaner <1800-PETROL,
2000> or <1600>).
4.
Fusible link box cover
5.
Connection of the battery harness
[positive battery terminal]
6.
Connection of the fusible link box
7.
Connection of the battery harness
[positive battery terminal]
8.
Battery terminal assembly [positive
battery terminal]
9.
Battery holder
10. Battery bolt
11. Battery
12. Battery tray
Removal steps (Continued)
BATTERY
CHASSIS ELECTRICAL
54A-15
<DIESEL>
CAUTION
If the battery current sensor or engine-ECU is replaced, make the battery current sensor learn the
zero point. (Refer to GROUP 00, Precautions Before Service
− Battery Current Sensor Calibration.)
ACB01840AB
12 ± 2 N·m
4
7
9
10
8
3
12
11
13
14
8.5 ± 1.5 N·m
4.0 ± 1.0 N·m
6.0 ± 2.0 N·m
1
2
5.0 ± 1.0 N·m
5
6
12 ± 2 N·m
Removal steps
1.
Battery current sensor
2.
Connection of the battery harness
[negative battery terminal]
3.
Battery terminal assembly [negative
battery terminal]
•
Air cleaner intake duct (Refer to GROUP
15
−).
4.
Fusible link box cover
5.
Connection of the battery harness
[positive battery terminal]
6.
Connection of fusible link box 1P
assembly
7.
Connection of fusible link box 6P
assembly
8.
Connection of the battery harness
[positive battery terminal]
9.
Battery terminal assembly [positive
battery terminal]
10. Battery holder
11. Battery bolt
12. Battery cover
13. Battery
14. Battery tray
Removal steps (Continued)
BATTERY
CHASSIS ELECTRICAL
54A-16
INSPECTION
BATTERY CURRENT SENSOR CHECK
<VEHICLES FOR EUR (EXCEPT 4AT)>
M1541002100405
CURRENT SENSOR RESISTANCE VALUE
Use the circuit tester to measure the resistance value
between battery current sensor connector terminals.
Standard value:
TEMPERATURE SENSOR RESISTANCE
VALUE
Using the circuit tester, measure the resistance value
between the battery current sensor connector termi-
nal No. 2 and No. 3.
Standard value:
Terminal No. (positive
terminal
− negative
terminal)
Resistance (k
Ω)
1
− 3
3
− 10
1
− 4
Less than 0.5
3
− 4
3
− 10
AC808952AB
Temperature (
°C)
Resistance (k
Ω)
0
4.5
− 7.2
25
1.6
− 2.5
40
0.96
− 1.40
AC808952AB
IGNITION SWITCH
CHASSIS ELECTRICAL
54A-17
IGNITION SWITCH
SPECIAL TOOLS
M1541200600163
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст