Mitsubishi Lancer (4A9 engine). Manual — part 225
ETACS
CHASSIS ELECTRICAL
54A-562
Inspection Procedure 6: The front door switch (passenger’s side) signal is not received.
CAUTION
Before replacing the ECU, ensure that the power supply circuit, the earth circuit and the communica-
tion circuit are normal.
COMMENTS ON TROUBLE SYMPTOM
If there is an error to the front door switch (passen-
ger’s side) input signal, the door switch (passenger’s
side) signal is no longer output to the communication
line.
ETACS-
ECU
Front Door Switch (Passenger's Side) Input Circuit
FRONT DOOR
SWITCH (RH) (LH)
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Grey R : Red P : Pink V : Violet PU : Purple SI : Silver
NOTE
: LHD
: RHD
AC701240
AU
Connector: C-313 <LHD>
ETACS-ECU
C-313 (BR)
AC701241
BA
Connector: C-313 <RHD>
ETACS-ECU
C-313 (BR)
AC801769AI
Connector: D-25
AC612722
BO
Connector: D-38
ETACS
CHASSIS ELECTRICAL
54A-563
PROBABLE CAUSES
• Malfunction of front door switch (RH) <LH drive
vehicles>
• Malfunction of front door switch (LH) <RH drive
vehicles>
• Malfunction of the ETACS-ECU
• Damaged harness wires and connectors
DIAGNOSIS PROCEDURE
STEP 1. Check the installation condition.
Check that the front door switch (RH) <LH drive vehi-
cles> or (LH) <RH drive vehicles> is installed to the
body correctly.
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Correct the installation condition.
STEP 2. Connector check: D-38 front door switch
(RH) <LH drive vehicles> or D-25 front door
switch (LH) <RH drive vehicles> connector
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Repair the defective connector.
STEP 3. Front door switch (RH) <LH drive
vehicles> or (LH) <RH drive vehicles> check
Refer to GROUP 42A
− Door .
Q: Is the check result normal?
YES :
Go to Step 4.
NO :
Replace the front door switch (RH) <LH
drive vehicles> or (LH) <RH drive vehicles>.
STEP 4. Connector check: C-313 ETACS-ECU
connector
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Repair the defective connector.
STEP 5. Wiring harness check between the D-38
front door switch (RH) <LH drive vehicles> or D-
25 front door switch (LH) <RH drive vehicles>
connector terminal No. 3 and the C-313 ETACS-
ECU connector terminal No. 16
Check the input lines for open circuit and short cir-
cuit.
Q: Is the check result normal?
YES :
Go to Step 6.
NO :
Repair the wiring harness.
STEP 6. M.U.T.-III data list
Open the front passenger's door.
OK: Normal condition is displayed.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
use Troubleshooting/inspection Service
Points
− How to Cope with Intermittent
Malfunction ).
NO :
Replace the ETACS-ECU.
Item No.
Item name
Normal
condition
Item 257
As door ajar switch
Open
ETACS
CHASSIS ELECTRICAL
54A-564
Inspection Procedure 7: The rear door switch (RH) signal is not received.
CAUTION
Before replacing the ECU, ensure that the power supply circuit, the earth circuit and the communica-
tion circuit are normal.
COMMENTS ON TROUBLE SYMPTOM
If there is an error to the rear door switch (RH) input
signal, the rear door switch (RH) signal is no longer
output to the communication line.
PROBABLE CAUSES
• Malfunction of rear door switch (RH)
• Malfunction of the ETACS-ECU
• Damaged harness wires and connectors
ETACS-
ECU
REAR DOOR
SWITCH (RH)
Rear Door Switch (RH) Input Circuit
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Grey R : Red P : Pink V : Violet PU : Purple SI : Silver
AC701240
AU
Connector: C-313 <LHD>
ETACS-ECU
C-313 (BR)
AC701241
BA
Connector: C-313 <RHD>
ETACS-ECU
C-313 (BR)
AC801769AJ
Connector: D-08
ETACS
CHASSIS ELECTRICAL
54A-565
DIAGNOSIS PROCEDURE
STEP 1. Check the installation condition.
Check that the rear door switch (RH) is installed to
the body correctly.
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Correct the installation condition.
STEP 2. Connector check: D-08 rear door switch
(RH) connector
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Repair the defective connector.
STEP 3. Rear door switch (RH) check
Refer to GROUP 42A
− Door .
Q: Is the check result normal?
YES :
Go to Step 4.
NO :
Replace the rear door switch (RH).
STEP 4. Connector check: C-313 ETACS-ECU
connector
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Repair the defective connector.
STEP 5. Wiring harness check between the D-08
rear door switch (RH) connector terminal No. 3
and the C-313 ETACS-ECU connector terminal
No. 8
Check the input lines for open circuit and short cir-
cuit.
Q: Is the check result normal?
YES :
Go to Step 6.
NO :
Repair the wiring harness.
STEP 6. M.U.T.-III data list
Open the rear right door.
OK: Normal condition is displayed.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
use Troubleshooting/inspection Service
Points
− How to Cope with Intermittent
Malfunction ).
NO :
Replace the ETACS-ECU.
Item No.
Item name
Normal
condition
Item 258
RR door ajar switch
Open
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст