Mitsubishi Lancer Evolution 7. Manual — part 372
SRS - Air Bag Modules and Clock Spring
52B-53
REMOVAL AND INSTALLATION
<Driver’s air bag module, clock spring>
Pre-removal Operation
Disconnect the Negative (-) Battery Terminal.
<RS: Steering wheel and air bag module separate type>
3
2
4
1
0.9 ± 0.2 N·m
0.9 ± 0.2 N·m
41 ± 8 N·m
Driver’s air bag module removal
steps
A
A"
1. Driver’s air bag module
Driver’s air bag module installation
steps
"
AA D Pre-installation inspection
1. Driver’s air bag module
D
Negative (-) terminal of the battery
connection
"
DA D Post-installation inspection
Clock spring removal steps
A
A"
1. Driver’s air bag module
A
B"
2. Steering wheel
3. Lower column cover
A
C"
4. Clock spring
Clock spring installation steps
"
AA D Pre-installation inspection
"
BA 4. Clock spring
3. Lower Column Cover
"
CA 2. Steering wheel
1. Driver’s air bag module
D
Negative (-) terminal of the battery
connection
"
DA D Post-installation inspection
SRS - Air Bag Modules and Clock Spring
52B-54
<RS-II: Steering wheel and air bag module incorporate type>
3
2
4
1
50 ± 5 N·m
2
Steering wheel-driver’s air bag
module assembly removal steps
A
D"
1. Cover
A
E"
2. Steering
wheel-driver’s
air
bag
module assembly
Steering wheel-driver’s air bag
module assembly installation steps
"
AA D Pre-installation inspection
2. Steering
wheel-driver’s
air
bag
module assembly
1. Cover
D
Negative (-) terminal of the battery
connection
"
DA D Post-installation inspection
Clock spring removal steps
A
D"
1. Cover
A
E"
2. Steering
wheel-driver’s
air
bag
module assembly
3. Lower Column Cover
A
C"
4. Clock spring
Clock spring installation steps
"
AA D Pre-installation inspection
"
BA 4. Clock spring
3. Lower Column Cover
"
CA 2. Steering
wheel-driver’s
air
bag
module assembly
1. Cover
D
Negative (-) terminal of the battery
connection
"
DA D Post-installation inspection
SRS - Air Bag Modules and Clock Spring
52B-55
<Front passenger’s air bag module>
1
Removal steps
D
Instrument panel assembly
(Refer to GROUP 52A - Instrument
panel.)
A
F
"
1. Passenger’s air bag module
Installation steps
"
AA D Pre-installation inspection
1. Passenger’s air bag module
D
Instrument panel assembly
(Refer to GROUP 52A - Instrument
panel.)
D
Negative (-) battery cable connection
"
DA D Post-installation inspection
REMOVAL SERVICE POINTS
A
A" DRIVER’S AIR BAG MODULE REMOVAL
1. Remove the air bag module mounting screw (torque
screw) from the steering wheel side.
2. Spread the lock outward to remove the connector by
prying with a flat-tipped screw driver as shown in the
illustration at left.
Caution
(1) Be careful not to remove the connector forcibly.
(2) Keep the removed driver’s air bag module facing
the pad surface upward in a clean and dry place.
locked
Connector
Flat-tipped screw
driver
locked
SRS - Air Bag Modules and Clock Spring
52B-56
A
B
"
STEERING WHEEL REMOVAL
A
C" CLOCK SPRING REMOVAL
Caution
Keep the removed clock spring in a clean and dry place.
A
D" COVER REMOVAL
Use the special tool to insert into the notch as shown in
the illustration and remove the cover.
A
E" STEERING WHEEL-DRIVER’S AIR BAG MODULE
ASSEMBLY REMOVAL
1. By sliding the A section (in the figure) of the clock spring
connector in the arrow direction, disconnect the connector.
2. Insert the hexagonal bit socket into the arrow section
in the figure. Completely loosen the bolt, and then remove
the steering wheel-driver’s air bag module assembly.
NOTE
Use a hexagonal bit socket or a hexagonal wrench having
an effective length of 75 mm or more in the hexagonal
section and the diameter of 8 mm or more.
MB990803
MB990784
A
Clock spring connector
Steering wheel-driver’s air bag
module assembly
Hexagonal bit
socket
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст