Mitsubishi Lancer Evolution 7. Manual — part 365
SRS -
Troubleshooting
52B-25
Code No.27 Driver’s seat belt pre-tensioner (squib)
system
Possible Cause
This code is output when open circuit occurs in the SRS-ECU driver’s seat belt
pre-tensioner (squib) circuit.
However, SRS warning lamp goes out when a normal operation is resumed
(diagnosis code is not cleared.)
D
Connector improper contact
D
Open in the driver’s seat pre-tensioner (squib)
circuit
D
SRS-ECU inoperable
<Check the driver’s seat belt pre-tensioner (squib)>
MUT-II self-diag code
D
Connect the dummy harness (MB991865) to the resistor harness
(MB991866).
D
Disconnect the driver’s seat belt pre-tensioner connector D-28*
1
and
D-26*
2
and insert the resistor harness (MB991866) behind the harness
side connector.
Caution
Do not directly insert a probe or other devices at the front of the
connector to avoid a possible decrease in the contact pressure.
D
Connect the negative (-) terminal of the battery
D
Check the diagnosis code again after erasing the memory.
Is code No.27 output?
YES
NO
Replace the driver’s seat belt pre-tensioner.
Replace the SRS-ECU.
Check the trouble
symptoms.
NG
Check the harness between the driver’s seat belt pre-tensioner
and the SRS-ECU, and repair if necessary.
NG
OK
OK
NG
Correct
Check connector: D-28
*
1
,
D-26
*
2
, C-133
*
1
, C-112
*
2
, C-124
Driver’s seat belt
pre-tensioner connector
<Check the circuit between the SRS-ECU and the driver’s
seat belt pretensioner>
Measure at the SRS-ECU connector C-41, the driver’s seat
belt pre-tensioner connector D-28*
1
and D-26
*2
.
D
Disconnect the SRS-ECU connector C-41 , the driver’s
seat belt pre-tensioner connector D-28*
1
and D-26*
2
, and
then measure at the harness side.
D
Continuity check between the following terminals
Connector C-41
D-28*
1
,
D-26*
2
29
–
2
30
–
1
Caution
Do not directly insert a probe or other devices at the
front of the connector to avoid a possible decrease in
the contact pressure.
OK: Continuity (2Ω or less)
Resistor harness
(MB991866)
Dummy resistor
(MB991865)
resistance (3Ω)
Instrumental panel
wiring harness
Connector C-41
D-28*
1
,
D-26*
2
connector
NOTE
*1: L.H. drive vehicles
*2: R.H. drive vehicles
SRS -
Troubleshooting
52B-26
Code No.28 Front passenger’s seat belt pre-tensioner
(squib) system
Possible Cause
This code is output when short circuit occurs between terminals of the
SRS-ECU front passenger’s seat belt pre-tensioner (squib) circuit.
However, SRS warning lamp goes out when a normal operation is resumed
(diagnosis code is not cleared.)
D
Connector engagement faulty or short bar faulty*
D
Short circuit between terminals of the front
passenger’s seat belt pre-tensioner (squib) circuit
D
Faulty connector
D
SRS-ECU inoperable
NOTE
*: The connector of the squib circuit contains a short bar (short-circuiting the positive (+) cable and the
negative (-) cable to avoid an erroneous deployment caused by static electricity when a connector is
not connected). Thus, when a connector is connected, the short bar may not be released due to improper
engagement of the connector or faulty connector as shown in the illustration below. Disconnect the connector
as shown in the illustration below, then reconnect it. Check that a diagnosis code is output again after
erasing the memory. If the diagnosis code is not output, the above-mentioned code is output due to
improper engagement of the connector.
C-41
C-133
*
1
,
C-112
*
2
D-28
*
1
,
D-26
*
2
SRS-ECU
Front passenger’s seat
belt pre-tensioner
NOTE
*1: L.H. drive vehicles
*2: R.H. drive vehicles
SRS -
Troubleshooting
52B-27
YES
NO
Replace the front passenger’s seat belt pre-tensioner.
<Check the front passenger’s seat belt pre-tensioner (squib)>
MUT-II self-diag code
D
Connect the dummy harness (MB991865) to the resistor harness
(MB991866).
D
Disconnect the front passenger’s seat belt pre-tensioner connector
D-28*
1
and D-26*
2
and insert the resistor harness (MB991866) behind
the harness side connector.
Caution
Do not directly insert a probe or other devices at the front of the
connector to avoid a possible decrease in the contact pressure.
D
Connect the negative (-) terminal of the battery
D
Check the diagnosis code again after erasing the memory.
Is code No.28 output?
Replace the SRS-ECU.
Check the trouble
symptoms.
NG
Check the harness between the front passenger’s seat belt
pre-tensioner and the SRS-ECU, and repair if necessary.
NG
Figure A
Short bar
Front view of SRS-ECU
connector C-41
(harness side)
OK
NG
Correct
Check connector: D-28*
1
, D-26
*2
, C-133*
1
, C-112
*2
, C-41
<Check the circuit between the SRS-ECU and the front
passenger’s seat belt pre-tensioner>
Measure at the SRS-ECU connector C-41.
D
Disconnect the SRS-ECU connector C-41.
D
Disconnect the front passenger’s seat belt pre-tensioner
connector D-28
*1
and D-26
*2.
Caution
Disconnect the connector and short-circuit the squib
circuit before releasing the short bar of the SRS-ECU
connector in the following operation.
D
Cable bands between terminals 27, 28 and the short bar
(width:3 mm, thickness:0.5 mm) between terminals 11 and
12 and the short bar, and release the short bar.
(See Figure A.)
Caution
As the short bar may not be releasable if inserted
insufficiently, insert more than 4 mm.
D
Measure at the harness side
D
Continuity check between terminals 27 and 28
Caution
Do not directly insert a probe or other devices at the
front of the connector to avoid a possible decrease in
the contact pressure.
OK: No continuity
Terminal
Cable
band and etc.
Section
A - A
A
A
4 mm or more
Resistor harness
(MB991866)
Dummy resistor
(MB991865)
resistance (3Ω)
Instrumental panel
wiring harness
Front passenger’s seat belt
pre-tensioner connector
Connector C-41
OK
NOTE
*1: L.H. drive vehicles
*2: R.H. drive vehicles
SRS -
Troubleshooting
52B-28
Code No.29 Front passenger’s seat belt pre-tensioner
(squib) system
Possible Cause
This code is output when open circuit occurs in the SRS-ECU front passenger’s
seat belt pre-tensioner (squib) circuit.
However, SRS warning lamp goes out when a normal operation is resumed
(diagnosis code is not cleared.)
D
Open in the front passenger’s seat pre-tensioner
(squib) circuit
D
Connector improper contact
D
SRS-ECU inoperable
<Check the circuit between the SRS-ECU and the front
passenger’s seat belt pre-tensioner>
Measure at the SRS-ECU connector C-41 , the front
passenger’s seat belt pre-tensioner connector D-28*
1
and
D-26*
2
.
D
Disconnect the SRS-ECU connector C-41 , the front
passenger’s seat belt pre-tensioner connector D-28*
1
and
D-26*
2
, and then measure at the harness side.
D
Continuity check between the following terminals
Connector C-41
D-28*
1
, Connector D-26*
2
28
–
2
27
–
1
Caution
Do not directly insert a probe or other devices at the
front of the connector to avoid a possible decrease in
the contact pressure.
OK: Continuity (2Ω or less)
YES
NO
Replace the front passenger’s seat belt pre-tensioner.
<Check the front passenger’s seat belt pre-tensioner (squib)>
MUT-II self-diag code
D
Connect the dummy harness (MB991865) to the resistor harness
(MB991866).
D
Disconnect the front passenger’s seat belt pre-tensioner connector
D-28*
1
and D-26*
2
and insert the resistor harness (MB991866) behind
the harness side connector.
Caution
Do not directly insert a probe or other devices at the front of the
connector to avoid a possible decrease in the contact pressure.
D
Connect the negative (-) terminal of the battery
D
Check the diagnosis code again after erasing the memory.
Is code No.29 output?
Replace the SRS-ECU.
Check the trouble
symptoms.
NG
Check the harness between the front passenger’s seat belt
pre-tensioner and the SRS-ECU, and repair if necessary.
NG
OK
OK
NG
Correct
Check connector: D-28*
1
, D-26*
2
, C-133*
1
, C-112*
2
, C-41
Resistor harness
(MB991866)
Dummy resistor
(MB991865)
resistance (3Ω)
Instrumental panel
wiring harness
Front passenger’s seat belt
pre-tensioner connector
Connector C-41
Connector D-28*
1
, D-26*
2
NOTE
*1: L.H. drive vehicles
*2: R.H. drive vehicles
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст