Mitsubishi Lancer Evolution 7. Manual — part 280
REAR AXLE -
Special Tools
27B-5
Tool
Use
Name
Number
MB991115
Oil seal installer
Press-fitting of oil seal
(AYC differential: used in combination with
MB990938)
MD998812
Installer cap
Press-fitting of oil seal
(torque transfer mechanism of vehicles with
AYC)
MD998813
Installer100
MD998829
Installer
adapter
(60)
MB990767
Front
hub
and
flange yoke holder
Removal, installation of the drive shaft nut
A
B
MB990241
A: MB990242
B: MB990244
Rear axle shaft
puller
A: Puller shaft
B: Puller bar
D
Removal of drive shaft
D
Removal of rear hub assembly
MB991354
Puller body
A
C
B
00005697
A: MB991017
B: MB990998
C: MB991000
A,B:Front hub re-
mover and in-
staller
C: Spacer
D
Temporary fixing of wheel bearing
D
Measurement of wheel bearing rotation
starting torque
D
Measurement of wheel bearing axial play
Use MB991000 (component of MB990998)
for the spacer.
REAR AXLE -
Special Tools
27B-6
Tool
Number
Name
Use
MB990685
Torque wrench
Measurement of the starting torque of wheel
bearing
MB990326
Preload socket
MB991113 or
MB990635
Steering
linkage
puller
Disconnection of ball joint
MB990641
Lower arm bush
(A) remover & in-
staller
Removal and press-fitting of differential
support member bush
MB991439
Bush remover &
installer
Removal and press-fitting of differential
support arm bush
MB991460
Plug
Prevention of differential oil from being
discharged and entry of foreign matter <AYC
differential>
MB990909
Working base
Supporting of the differential carrier
MB991116
Adapter
Support of differential carrier assembly
MB990810
Side bearing puller
D
Removal of the side bearing inner race
D
Removal of the companion flange
REAR AXLE -
Special Tools
27B-7
Tool
Use
Name
Number
MB990850
End yoke holder
D
Removal of the self-locking nut
D
Adjustment of the drive pinion turning
torque
MB990339
Bearing puller
Drive pinion rear bearing inner race removal
MB990648
Bearing remover
B
A
MB990835
A: MB990836
B: MB990392
Drive pinion setting
gauge set
A: Drive
pinion
gauge assem-
bly
B: Cylinder
gauge
Adjustment of drive pinion height
MB990988
Side gear holding
tool set
Measurement of clutch plate preload (vehicles
with mechanical LSD)
MB990728
Side & rear bearing
inner race installer
Press-fitting of drive pinion rear bearing inner
race
MB990727
Oil seal installer
Press-fitting of drive pinion oil seal
MB990813
Tap
Removal of adhesive
REAR AXLE -
Special Tools/Troubleshooting <AYC>
27B-8
Number
Name
O.D.
mm
Box
MB990551
Box
–
C
Base
MB990989
Base
–
A
B
C
Base
MB990990
Tool A
25
A
Tool
MB990991
Tool B
28
Tool
MB990992
Tool C
31
Installer adapter
Brass bar
Bar (one-touch type)
A
B
C
Toolbox
Tool number
O.D.
mm
Tool number
O.D.
mm
A
MB990926
39
A
MB990933
63.5
MB990927
45
MB990934
67.5
MB990928
49.5
MB990935
71.5
MB990929
51
MB990936
75.5
MB990930
54
MB990937
79
MB990931
57
B
MB990938
-
MB990932
61
C
MB990939
-
TROUBLESHOOTING <AYC>
BASIC TROUBLESHOOTING CONDITIONS
Refer to GROUP 00 – How to Use Troubleshooting/Inspection Service Points.
NOTE
Before starting the troubleshooting procedure, make sure that the following items have been checked
okay.
D
The correct steering wheel has been properly installed in the neutral position of the steering column
shaft.
D
Tire and wheel sizes are correct with correct specifications. Inflation pressure, balance, and wear
conditions are okay.
D
Wheel alignment is correct.
D
The engine, suspension, and other parts have not been remodeled so as to affect the AYC system.
DIAGNOSIS FUNCTION
READING THE DIAGNOSIS CODES
Read the diagnosis code using MUT-II or ACD mode indicator
lamp. (Refer to GROUP 00 – How to Use Troubleshooting/
Inspection Service Points.)
NOTE
Connect the MUT-II to the 16-pin diagnosis connector.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст