Mitsubishi Lancer Evolution 7. Manual — part 155
ENGINE -
Engine Assembly
11A-45
67 ± 7 N·m*
23
33
24
29
30
31
32
27
22
98 ± 10 N·m*
5.0 ± 1.0 N·m
(Engine oil)
20
21
19
25
42 ± 2 N·m
22 ± 4 N·m
40 ± 5 N·m
42 ± 2 N·m
26
26
28
34
22 ± 4 N·m
12 ± 2 N·m
19. Brake booster vacuum hose
connection
20. Purge hose connection
21. Power steering oil pressure switch
connector
22. Heat protector
A
B"
23. Power steering oil pump, bracket and
oil reservoir assembly
24. A/C compressor connector
<Vehicle with A/C>
A
B"
25. A/C compressor <Vehicle with A/C>
26. Engine oil cooler tube gasket
27. Engine oil cooler feed hose connection
28. Engine oil cooler return hose
connection
29. Heater hose connection
30. Fuel return hose connection
"
CA 31. Fuel high pressure hose connection
"
CA 32. O-ring
D
Transfer assembly
(Refer to Group 22.)
D
Transmission assembly
(Refer to Group 22.)
A
C" "BA 33. Engine mounting bracket and stopper
assembly
A
D" "AA 34. Engine assembly
ENGINE -
Engine Assembly
11A-46
REMOVAL SERVICE POINTS
A
A" DRIVE BELT REMOVAL
Due to the adoption of the Serpentine drive system with the
auto-tensioner, the following operation is required:
1. Insert the 12.7sq. spinner handle into the tool hole of
the auto-tensioner and rotate it counterclockwise until
the auto-tensioner reaches to the stopper.
2. Align hole A with hole B for fixing by inserting the L
shaped-hexagon wrench, then remove the drive belt.
Caution
When the drive belt is reused, use a chalk to indicate
an arrow of rotation direction on the back of the belt
so that it can be re-assembled in the same direction
as before.
A
B" POWER STEERING OIL PUMP, BRACKET AND
OIL RESERVOIR ASSEMBLY / A/C COMPRESSOR
REMOVAL
Remove the power steering oil pump, bracket, oil reservoir
and A/C compressor with the hose attached from the bracket.
NOTE
Tie the removed oil pump and A/C compressor with a rope
and set aside where they cannot hinder the removal of the
engine assembly.
A
C" ENGINE MOUNTING BRACKET AND STOPPER
ASSEMBLY REMOVAL
1. Support the engine with a garage jack.
2. Remove special tool (MZ203827).
(Tool used for removal of transmission assembly)
3. Hold the engine assembly with a chain block.
4. Support the engine oil pan with a garage jack via a block
of wood cut without applying the weight of the engine
and remove the engine mounting bracket and stopper
assembly.
Bore A
L-shaped
hexagon
wrench
Bore B
MZ203827
MB991453
MB991453
ENGINE -
Engine Assembly
11A-47
A
D" ENGINE ASSEMBLY REMOVAL
After checking that all the cables, hoses, and harness
connectors have been disconnected, lift the engine with a
chain block slowly and remove the engine assembly located
at the upper engine room.
INSTALLATION SERVICE POINTS
"
AA ENGINE ASSEMBLY INSTALLATION
Install the engine assembly while checking that none of cables,
hoses, or harness connectors, etc. has been engaged.
"
BA ENGINE MOUNTING BRACKET AND STOPPER
ASSEMBLY INSTALLATION
1. Support the engine oil pan with a garage jack via a block
of wood cut adjusting the engine position and install the
engine mounting bracket and stopper assembly. Position
the engine mounting stopper so that a mark indicated
by an arrow can face the direction shown in the illustration.
2. Support engine with garage jack.
3. Remove the chain block and hold the engine assembly
with the special tool.(Tool used for removal of transmission
assembly)
"
CA O-RING/FUEL HIGH PRESSURE HOSE
INSTALLATION
1. Apply small quantity of new engine oil on O-ring.
Caution
Do not let engine oil get into the delivery pipe.
2. Install the fuel high pressure pipe to the delivery pipe
rotating in both directions without damaging the O-ring
and check that it rotates smoothly.
3. In case of not rotating smoothly, remove the fuel high
pressure hose and insert it to the delivery pipe again
after checking damage of the O-ring since there is a
possibility of O-ring engagement.
4. Tighten fuel high pressure hose mounting bolt to the
specified torque.
Tightening Torque: 5.0 ± 1.0 N·m
Engine mounting stopper
Engine side
<Vehicle: Top view>
<Vehicle: Rear view>
Engine side
NOTES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст