Mitsubishi Lancer Evolution 7. Manual — part 385
CHASSIS ELECTRICAL -
Headlamp Assembly
CHASSIS ELECTRICAL -
Headlamp Assembly
CHASSIS ELECTRICAL -
Headlamp Assembly
54A-29
HEADLAMP BULB (HIGH BEAM)REPLACEMENT
(1) Disconnect battery.
(2) Disconnect connector.
(3) Screw out socket to pull out bulb.
(4) After bulb is replaced, properly reconnect connector.
Caution
Do not touch bulb surface bare-handed or with dirty
gloves. If dirt is attached on glass surface of the bulb,
immediately use alcohol or thinner to remove dirt, and
install the bulb after well dried.
POSITION LAMP BULB REPLACEMENT
1. Remove the splash shield.
2. Disconnect the connector and remove the socket of the
position lamp by turning to left.
Caution
Do not touch bulb surface bare-handed or with dirty
gloves. If dirt is attached on glass surface of the bulb,
immediately use alcohol or thinner to remove dirt, and
install the bulb after well dried.
FRONT TURN-SIGNAL LAMP BULB
REPLACEMENT
1. Remove the splash shield.
2. Disconnect the connector and remove the socket of the
front turn signal lamp by turning to left.
Caution
Do not touch bulb surface bare-handed or with dirty
gloves. If dirt is attached on glass surface of the bulb,
immediately use alcohol or thinner to remove dirt, and
install the bulb after well dried.
HEADLAMP AUTO CUT ADJUSTMENT
PROCEDURE
Headlamps are controlled smart wiring system (SWS). For
adjustment procedure of headlamp auto lamp and headlamp
auto cut, refer to GROUP 54B.
HEADLAMP AUTO CUT FUNCTION CHECK
When lighting switch is turned ON (to HEAD position) with
ignition switch removed from ignition key cylinder and driver’s
door is opened, ensure that headlamps are switched off after
one second. When headlamps are inoperative, perform
troubleshooting. (Refer to GROUP 54B.)
Headlamp bulb
<High beam>
Position lamp
CHASSIS ELECTRICAL -
Headlamp Assembly
CHASSIS ELECTRICAL -
Headlamp Assembly
54A-30
HEADLAMP ASSEMBLY
REMOVAL AND INSTALLATION
2
3
1
AY2103AU
1. Headlamp leveling switch
Headlamp removal steps
D
Front bumper (Refer to GROUP 51)
2. Air guide panel
3. Headlamp assembly
INSPECTION
HEADLAMP LEVELING SWITCH CONTINUITY CHECK
Switch Position
Resistance between the termi-
nal 4 and 5 (Ω)
0
120
1
300
2
620
3
1.1 k
4
2 k
CHASSIS ELECTRICAL -
Side Turn-signal Lamp/Room Lamp
54A-31
SIDE TURN-SIGNAL LAMP
SPECIAL TOOL
Tools
Number
Name
Use
MB990784
Ornament remover
Side turn-signal lamp removal
SIDE TURN-SIGNAL LAMP
REMOVAL SERVICE POINT
Use special tool, etc. to press and deflect hook to vehicle
front from fender, and unhook the pawls to remove side
turn-signal lamp.
INSTALLATION SERVICE POINT
Insert pawls into fender panel and install side turn-signal lamp.
ROOM LAMP
TROUBLESHOOTING
For troubleshooting of room lamp, refer to GROUP 54B.
Side turn-signal lamp
MB990784
Front of vehicle
AX0386CA
Fender pane
Hook
Tab
Fender panel
Front of vehicle
CHASSIS ELECTRICAL
-
Rear Combination Lamp
54A-32
REAR COMBINATION LAMP
SPECIAL TOOL
Tool
Number
Name
Use
MB990784
Ornament remover
Rear combination lamp removal
TROUBLESHOOTING
For troubleshooting on rear combination lamps, refer to GROUP 54B.
REAR COMBINATION LAMP
REMOVAL AND INSTALLATION
4
2
1
5
3
1. Rear fog lamp switch
Removal steps
2. Rear combination lamp assembly
3. Rear combination lamp body
4. Socket assembly
5. Bulb
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст