Mitsubishi Lancer Evolution 7. Manual — part 377
SRS -
Air Bag Module and Seat Belt Pre-tensioner
Disposal Procedures
52B-73
(6) Disconnect the deployment harnesses as far from
the front passenger’s air bag module as possible and
connect the harnesses to the battery removed from
the vehicle.
Caution
1) Before the deployment, see that no one is near
the front passenger’s air bag module.
2) The deployment makes the inflator of the front
passenger’s air bag very hot. Before handling
the inflator, wait more than 30 minutes for
cooling.
3) If the front passenger’s air bag module fails to
deploy although the procedure is respected,
do not go near the module. Contact your local
distributor.
(7) Discard the deployed air bag module as specified
in Deployed Air Bag Module Disposal Procedures.
(Refer to P.52B-75.)
Seat belt pre-tensioner
(1) Remove the seat belt with pre-tensioner from the
vehicle. (Refer to P.52B-61.)
Caution
Once disconnected, both electrodes of the seat
belt
pre-tensioner
are
short-circuited
automatically to prevent accidental deployment
caused by static etc. Still, in consideration of the
accidental deployment, store the air bag module
on flat place with deployment surface facing up.
Also, do not put anything on it.
(2) Connect deployment harness 6 m or longer with the
SRS air bag adapter harness respectively. Insulate
the connection with tape.
Moreover, the ends of the operation harness should
be connected (short-circuited) to each other. Thus,
it prevents the seat belt pre-tensioner from accidental
deployment caused by static and etc.
Deployment harnesses
SRS air bag
adapter
harness
MR686560
Shorted
6 m long
or more
Insulation tape
Deployment
harnesses
SRS -
Air Bag Module and Seat Belt Pre-tensioner
Disposal Procedures
52B-74
(3) Route a thick wire through the holes in the seat belt
retractor bracket to secure at the top of the wheel
(convex part). (two locations)
(4) Connect the seat belt pre-tensioner connector to the
the SRS air bag adapter harness with the operation
harness attached.
(5) Pull out the seat belt outside the tyre.
Caution
Place the connector of the SRS air bag adapter
harness so that it is not clamped by the tyres at
deployment.
(6) Place an old tyre (without a wheel) on the tyre, which
the seat belt with pre-tensioner is secured on.
(7) Disconnect the deployment harness as far fromthe
seat belt pre-tensioner as possible and connect the
both terminals of the battery removed from the vehicle.
Then deploy.
Caution
1) Before the deployment, see that no one is near
the seat belt pre-tensioner.
2) Before handling the insulator, wait for a while
for cooling.
3) If the seat belt pre-tensioner fails to operate
although the procedure is respected, do not go
near the seat belt pre-tensioner. Contact your
local distributor.
(8) Discard the operated seat belt pre-tensioner
according to Disposal Procedure.(Refer to P.52B-75.)
Seat belt pre-tensioner
Deployment harness
Old tyres without
wheels
Deployment harness
SRS -
Air Bag Module and Seat Belt Pre-tensioner
Disposal Procedures
52B-75
DEPLOYED AIR BAG MODULE OR OPERATED
SEAT
BELT
PRE-TENSIONER
DISPOSAL
PROCEDURES
Discard the deployed air bag module or the operated seat
belt with pre-tensioner paying attention to the following items.
1. The deployment makes the inflator of the air bag or the
operation of the seat belt pre-tensioner very hot. Wait
for more than 30 minutes for cooling before handling
the inflator.
2. Do not apply any water or oil onto the deployed air bag
module or the operated seat belt pre-tensioner.
3. Wear gloves and protective glasses before handing the
deployed air bag module or the operated seat belt
pre-tensioner since materials on those parts may cause
irritation to eyes or skin.
Caution
If after following these precautions, any material does
get into the eyes or on the skin, immediately rinse the
affected area with a large amount of clean water.
If any irritation develops, seek medical attention.
4. Discard the air bag module and the seat belt with
pre-tensioner after placing them into a strong vinyl bag
for sealing.
5. Be sure to always wash your hands after completing this
operation.
Strong
vinyl bag
Air bag module,
seat belt with
pre-tensioner
NOTES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст