Mitsubishi Lancer Evolution 7. Manual — part 222
INTAKE AND EXHAUST -
Intercooler Water Spray
ILL
15-13
INSPECTION
1. WATER SPRAY SWITCH CONTINUITY CHECK
Switch position Terminal No
Switch position Terminal No.
p
AUTO
MANUAL EARTH
ILL (+)
ILL (-)
1
2
3
5
6
AUTO
NEUTRAL
MAN
2. WATER SPRAY MOTOR CHECK
(1) Check the water spray motor with the washer tank
attached after the washer tank is supplied with water.
(2) Check that the water is supplied with strong pressure
after energizing terminal number 1 with battery voltage
and earthing terminal number 2.
<Water spray switch>
<Water spray motor>
INTAKE AND EXHAUST -
Secondary Air Supply System
15-14
SECONDARY AIR SUPPLY SYSTEM
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
D
Air Duct Removal and Installation (Refer to P.15-8.)
D
Strut Tower Bar Removal and Installation (Refer to GROUP 42.)
1
2
3
4
5
49 ± 5 N·m
14 ± 1 N·m
22 ± 4 N·m
14 ± 1 N·m
14 ± 1 N·m
20 ± 2 N·m
6
8
9
10
22 ± 4 N·m
24 ± 3 N·m
23 ± 4 N·m
11 ± 1 N·m
Air pipe C
5.9 ± 1.0 N·m
7
7
11
Removal steps
1. Control harness connector
connection
2. Heat protector
3. Vacuum hose connection
D
Air pipe C (Refer to P.15-9.)
4. Vacuum pipe
5. Secondary air hose
6. Secondary air pipe assembly
"
AA 7. Gasket
"
BA 8. Gasket
9. Secondary air control valve
10. Engine hanger
11. Secondary air control valve bracket
INTAKE AND EXHAUST -
Secondary Air Supply System
15-15
INSTALLATION SERVICE POINTS
"
AA GASKET INSTALLATION
Install the gasket so that its salient can face towards the
direction as shown in the illustration.
"
BA GASKET INSTALLATION
Install the gasket so that its protrusion can face towards the
direction as shown in the illustration.
Salient
Secondary air pipe assembly
Protrusion
INTAKE AND EXHAUST -
Intake Manifold
15-16
INTAKE MANIFOLD
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
D
Air Duct Removal and Installation (Refer to P.15-8.)
D
Strut Tower Bar Removal and Installation
(Refer to GROUP 42.)
D
Under Cover Removal and Installation
(Refer to GROUP 51 - Front Bumper.)
D
Engine Coolant Draining and Supplying
(Refer to GROUP 14 - On-vehicle Service.)
D
Throttle Body Removal and Installation (Refer to
GROUP 13A - Throttle Body.)
D
Crossmember Bar Removal and Installation (Refer
to GROUP 32 - Engine Roll Stopper, Centermember.)
D
Front Exhaust Pipe Removal and Installation (Refer
to GROUP 15 - Exhaust Pipe and Main Muffler.)
D
Secondary Air Control Valve Bracket Removal and
Installation (Refer to P.15-14.)
D
Engine Oil Draining and Supplying
1
2
3
4
5
6
7
8
10
11
12
14
13
15
16
17
18
9
11 ± 1 N·m
3.0 ± 0.5 N·m
13 ± 1 N·m
(Engine oil)
(Engine oil)
5.0 ± 1.0 N·m
14
8
Removal steps
1. Center cover
2. Oxygen sensor connector
connection
3. Injector connector connection
4. Fuel pressure solenoid valve
connector connection
5. Purge control solenoid valve
connector connection
6. Knock sensor connector connection
7. Vacuum hose connection
8. Vacuum hose
9. Fuel return hose connection
"
AA 10. Fuel high-pressure hose connection
11. O-ring
A
A"
12. Delivery pipe, Injector and fuel
pressure regulator assembly
13. Insulator
14. Insulator
15. Oil level gauge and guide
16. O-ring
17. Brake booster vacuum hose
connection
18. Purge hose connection
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст