Mitsubishi Lancer Evolution 7. Manual — part 214
FUEL SUPPLY - Fuel Tank
13B-7
DISASSEMBLY AND REASSEMBLY
<FUEL PUMP AND GAUGE ASSEMBLY>
1
2
3
4
5
6
7
9
8
10
11
12
13
Removal steps
1. Fuel gauge unit
2. Gauge harness
3. Bracket
4. Fuel pump cushion
5. Fuel pump
6. Spacer
"
AA 7. Grommet
8. Assist pump
9. Fuel suction hose
10. Fuel return hose
11. Cap
"
AA 12. O-ring
13. Fuel filter assembly
FUEL SUPPLY - Fuel Tank
13B-8
<PIPE AND GAUGE ASSEMBLY>
2
3
6
1
4
5
1.2 ± 0.2 N·m
Removal steps
1. Packing
2. Filter
3. Gauge unit
4. Connector
"
AA 5. O-ring
6. Pipe assembly
INSTALLATION SERVICE POINT
"
AA O-RING/GROMMET INSTALLATION
Apply a fuel to O-ring and grommet before installing them,
to prevent them from being damaged or twisted.
14-1
ENGINE COOLING
CONTENTS
. . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
Radiator Cap Opening Pressure Check
. . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .
Radiator Fan Relay Continuity Check
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE COOLING -
General Information/
Service Specifications/Lubricant/Sealant
14-2
GENERAL INFORMATION
The cooling system is designed to keep every part
of the engine at appropriate temperature in
whatever condition the engine may be operated.
The cooling method is of the water-cooled, pressure
forced circulation type in which the water pump
pressurizes coolant and circulates it throughout the
engine. If the coolant temperature exceeds the
prescribed temperature, the thermostat opens to
circulate the coolant through the radiator as well
so that the heat absorbed by the coolant may be
radiated into the air.
The water pump is of the centrifugal type and is
driven by the drive belt from the crankshaft.
The radiator is the corrugated fin, down flow type.
The cooling fan is controlled by the radiator fan
controller and engine-ECU depend on driving
conditions.
Item
Specification
Radiator performance kJ/h
216,700
SERVICE SPECIFICATIONS
Items
Standard value
Limit
Radiator cap opening pressure kPa
93 - 123
83
Range of coolant antifreeze concentration of radiator %
30 - 60
-
Thermostat
Valve opening temperature of thermostat _C
80 ± 1.5
-
Full-opening temperature of thermostat _C
93
-
Valve lift (at 93_C) mm
9.5 or more
-
LUBRICANT
Item
Specified coolant
Quantity L
Engine coolant
MITSUBISHI GENUINE COOLANT or equivalent
6.0
Engine coolant
(including reserve tank)
MITSUBISHI GENUINE COOLANT or equivalent
6.0
SEALANT
Item
Specified sealant
Remark
Cylinder block drain plug
3M Nut Locking Part No. 4171 or equivalent
Drying sealant
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст