Mitsubishi Lancer Evolution 7. Manual — part 218
ENGINE COOLING -
Water Hose and Water Pipe/Radiator
14-15
REMOVAL SERVICE POINT
A
A" RADIATOR UPPER HOSE/RADIATOR LOWER
HOSE DISCONNECTION
After making mating marks on the hose and the hose clamp,
disconnect the hose.
INSTALLATION SERVICE POINTS
"
AA O-RING INSTALLATION
Fit an O-ring into the groove of the water inlet pipe and
apply water to the circumference of the O-ring or the
inside of the mounting surface of the pipe for insertion.
CAUTION
Do not let the O-ring get contaminated with grease, such
as engine oil.
"
BA WATER INLET PIPE INSTALLATION
After installing the water outlet fitting and the thermostat
case assembly, tighten the mounting bolt of the water
inlet pipe to the specified torque.
"
CA RADIATOR LOWER HOSE/RADIATOR UPPER
HOSE CONNECTION
1. Insert each hose as far as the projection of the water
inlet pipe or water outlet fitting.
2. Align the mating marks on the radiator hose and hose
clamp, and then connect the radiator hose.
INSPECTION
WATER PIPE AND HOSE CHECK
Check the water pipe and hose for cracks, damage, clog
and replace them if necessary.
RADIATOR
REMOVAL AND INSTALLATION
Pre-remobal and Post-installation Operation
D
Engine Coolant Draining and Supplying (Refer to P.14-6.)
D
Under Cover Removal and Installation (Refer to GROUP 51 - Front Bumper.)
D
Air Cleaner Assembly Removal and Installation (Refer to GROUP 15.)
D
Air Hose E, Air Pipe C, Air hose D Removal and Installation (Refer to GROUP 15 - Intercooler.)
D
Battery and Battery Tray Removal and Installation
Water pump or
thermostat case
O-ring
Warter inlet pipe
ENGINE COOLING -
Radiator
14-16
1
2
3
4
5
6
7
12 ± 2 N·m
9
16
14
19
18
12
17
10
8
13
15
10
20
21
12 ± 2 N·m
5.0 ± 1.0 N·m
3.5 ± 0.4 N·m
4.5 ± 0.4 N·m
4.0 ± 0.4 N·m
13
11
12 ± 1 N·m
Radiator removal steps
1. Radiator drain plug
2. Radiator cap
3. Reserve tank hose
4. Reserve tank
5. Reserve tank cap
6. Reserve tank hose
7. Reserve tank bracket
A
A" "AA 8. Radiator upper hose
A
A" "AA 9. Radiator lower hose
10. Upper insulator
A
B"
11. Air Pipe B mounting bolt
12. Radiator assembly
13. Lower insulator
14. Radiator fan controller connector
15. Radiator fan controller, radiator fan
motor, fan and shroud assembly
Radiator fun controller and radiator
fun motor removal steps
A
B"
11. Air Pipe B mounting bolt
14. Radiator fan controller connector
16. Radiator fan motor connector
17. Radiator fan controller
18. Radiator fan motor fan and shroud
assembly
19. Fan
20. Radiator fan motor
21. Shroud
ENGINE COOLING -
Radiator
ENGINE COOLING -
Radiator
14-17
REMOVAL SERVICE POINTS
A
A" RADIATOR UPPER HOSE/RADIATOR LOWER
HOSE REMOVAL
After making mating marks on the radiator hose and the hose
clamp,disconnect the radiator hose.
A
B" AIR PIPE B MOUNTING BOLT REMOVAL
After removing the bolt, position air pipe B out of the way
so that the pipe does not interfere with the radiator assembly
or the radiator fan motor, the fan and shroud assembly.
INSTALLATION SERVICE POINT
"
AA RADIATOR LOWER HOSE/RADIATOR UPPER
HOSE INSTALLATION
1. Insert each hose as far as the projection of the water
inlet pipe, water outlet fitting or radiator.
2. Align the mating marks on the radiator upper hose and
hose clamp, and then connect the radiator hose.
NOTES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст