Mitsubishi Lancer Evolution 7. Manual — part 294
REAR AXLE
- Hydraulic Unit <Vehicles with ACD+AYC>
27B-61
HYDRAULIC UNIT <VEHICLES WITH ACD+AYC>
REMOVAL AND INSTALLATION
Caution
(1) When connecting the return hose and suction hose, do not apply lubricant.
(2) No foreign matter should be allowed in the hydraulic piping and joints.
Pre-removal Operation
D
Trunk Side Trim Removal (Refer to GROUP 52A.)
D
Hydraulic Piping Fluid Draining
Post-installation Operation
D
Hydraulic Piping Fluid Filling and Bleeding
(Refer to P.27B-17 and P.27B-19.)
D
Trunk Side Trim Installation (Refer to GROUP 52A.)
1
2
7
6
4
8
9
10
3
11
34 ± 5 N m*
1
24 ± 4 N m
12 ± 2 N m
26 ± 4 N m*
2
5
12 ± 2 N m
12 ± 2 N m
18 ± 2 N m
34 ± 5 N m*
1
26 ± 4 N m*
2
18 ± 2 N m
12 ± 2 N m
34 ± 5 N m*
1
26 ± 4 N m*
2
12 ± 2 N m
NOTE:
*
1:
Thread is not lubricated
*
2:
Thread is lubricated
Removal steps
1. Dust guard
2. Reservoir hose assembly and hy-
draulic unit connection
3. Hydraulic unit hose assembly and
hydraulic unit connection
4. Transfer connector assembly and
hydraulic unit connection
5. Hydraulic unit bracket assembly
mounting bolt
"
BA 6. Hydraulic unit assembly
7. Hydraulic unit bracket
D
Stabilizer bar to differential support
arm connection (Refer to GROUP 34.)
D
Differential support arm (Refer to P.
27B-55.)
A
A"
8. Hydraulic unit hose assembly <ve-
hicles with ACD+AYC>
9. Transfer connector assembly
"
AA 10. Reservoir hose assembly
11. Oil reserve
REAR AXLE
- Hydraulic Unit <Vehicles with ACD+AYC>
REAR AXLE
- Hydraulic Unit <Vehicles with ACD+AYC>
27B-62
REMOVAL SERVICE POINTS
A
A" HYDRAULIC UNIT HOSE ASSEMBLY REMOVAL
1. Disconnect the hydraulic unit side pipe and hose.
2. Put down the differential support arm, remove the
hydraulic unit hose assembly.
HYDRAULIC UNIT DISPOSAL
Should the hydraulic unit be discarded, drill a hole in the
accumulator at the illustrated position beforehand in order
to release the inside gas.
Caution
(1) The hydraulic unit has its accumulator filled with a high
pressure gas. Never throw it into a fire. Also, never
attempt to disassemble, press, weld or melt it.
(2) When drilling a hole in the accumulator, be sure to
wear safety goggles since drill chips may blow out
together with the gas.
INSTALLATION SERVICE POINTS
"
AA RESERVOIR HOSE ASSEMBLY INSTALLATION
Insert the reservoir hose assembly to the positioning spool.
"
CA HYDRAULIC UNIT ASSEMBLY INSTALLATION
Hook the hydraulic unit assembly hook to the rear floor side
member and tighten the hydraulic unit assembly mounting
bolt.
Hose
Pipe
Hydraulic unit
hose assembly
Differential support arm
Positioning
spool
Nipple
Reservoir hose
assembly
Hook
Rear floor side member
31-1
WHEEL AND TYRE
CONTENTS
. . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
WHEEL AND TYRE -
General Information/Service Specifications
31-2
GENERAL INFORMATION
The wheels and tyres of the following specifications
have been established.
SPECIFICATIONS
Items
RS (standard)
RS (option), RS-II
Wheel
Type
Steel type
Aluminium type
Size
15 × 6JJ
17 × 8JJ
Amount of wheel offset mm
46
38
Pitch
circle
diameter
(P.C.D.) mm
114.3
114.3
Tyre
Size
205/65R15 94H
235/45ZR17
Spare wheel
Type
Steel type
Steel type
p
Size
16 × 4T
17 × 4T
Amount of wheel offset mm
40
30
Pitch
circle
diameter
(P.C.D.) mm
114.3
114.3
Spare tyre (High pressure)
Size
T125/70D16
T125/70D17
SERVICE SPECIFICATIONS
Items
Limit
Tread depth of tyre mm
1.6
Wheel runout (Radial runout) mm
Steel wheel
1.2 or less
Aluminium wheel
1.0 or less
Wheel runout (Lateral runout) mm
Steel wheel
1.2 or less
Aluminium wheel
1.0 or less
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст