Mitsubishi Evolution X. Manual — part 837
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-31
STEP 11. Measure the voltage at ETACS-ECU connector
C-304.
(1) Disconnect ETACS-ECU connector C-304 and measure the
resistance available at the wiring harness side of the
connector.
(2) Ignition switch: ACC
(3) windshield wiper switch: HI
(4) Measure the voltage between C-304 ETACS-ECU
connector terminal No. 5 and body ground.
OK: Battery voltage
(5) windshield wiper switch: LO
(6) Measure the voltage between C-304 ETACS-ECU
connector terminal No. 6 and body ground.
OK: Battery voltage
Q: Is the measured voltage approximately 12 volts (battery
positive voltage)?
YES : Go to Step 13.
NO : Go to Step 12.
STEP 12. Check the wiring harness between ETACS-ECU
connector C-304 (terminals 5, 6) and windshield wiper
motor connector A-06 (terminals 4, 1).
• Check the input and output lines for open or short circuit.
Q: Is the wiring harness between ETACS-ECU connector
C-304 (terminals 5, 6) and windshield wiper motor
connector A-06 (terminals 4, 1) in good condition?
YES : Go to Step 13.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Cables and wire check
.
STEP 13. Retest the system.
Check that the windshield wipers work normally.
Q: Is the check result normal?
YES : Intermittent malfunction. Refer to GROUP 00, How to
cope with intermittent malfunction
.
NO : Replace the ETACS-ECU.
AC608254CQ
Harness side: C-304
AC608254 CR
Harness side: C-304
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-32
INSPECTION PROCEDURE 2: The windshield wipers do not work when the wiper switch is at the
"INT", "Washer" or "Mist" position. However, the wipers work at low speed when the switch is at the
"Lo" or "Hi" position.
.
TECHNICAL DESCRIPTION (COMMENT)
This system may be at fail-safe mode if the LIN com-
munication line is defective.
If the system cannot receive any signal from the col-
umn switch (windshield wiper and washer switch)
due to a open circuit in the LIN communication line or
other reasons, the system will enter the fail-safe
mode when the ignition switch is at the "ACC" posi-
tion.
.
AC708841
ETACS-ECU
ACC
RELAY3
Windshield Wiper Motor Circuit
WINDSHIELD
WIPER
MOTOR
CIRCUIT
BREAKER
· WINDSHIELD WIPER HI SPEED SWITCH
· WINDSHIELD WIPER INTERMIT SWITCH
· WINDSHIELD WIPER LO SPEED SWITCH
· WINDSHIELD WIPER MIST SWITCH
INPUT SIGNAL
WINDSHIELD
WIPER SPEED
SWITCHING
RELAY
AB
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-33
TROUBLESHOOTING HINTS
• The wiring harness or connectors may have
loose, corroded, or damaged terminals, or termi-
nals pushed back in the connector
• The column switch may be defective
• The ETACS-ECU may be defective
• The LIN bus line may be defective
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB992006: Extra Fine Probe
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A
STEP 1. Use the scan tool MB991958 to check if an
ETACS-related diagnostic trouble code is set.
Connect the scan tool. Refer to GROUP 54A ETACS, "How to
connect the scan tool (M.U.T.-III)
."
Q: Is the diagnostic trouble code set?
YES : Diagnose the ETACS-ECU. Refer to GROUP 54A
ETACS, "Diagnostic trouble code chart
."
NO : Go to Step 2.
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-34
STEP 2. Using scan tool MB991958, check data list.
Check the input signal related to the windshield wiper opera-
tion.
• Ignition switch: ACC
• Operate the windshield wiper switch at each switch posi-
tion.
OK: Normal condition is displayed.
Q: Is the check result normal?
YES : Go to Step 3.
NO : Troubleshoot the ETACS-ECU. Refer to ETACS,
Diagnosis - Inspection Procedure 12 "ETACS-ECU
does not receive any signal from the column switch
signal."
.
STEP 3. Retest the system.
Check that the windshield wipers work normally.
Q: Is the check result normal?
YES : Intermittent malfunction. Refer to GROUP 00, How to
cope with intermittent malfunction
.
NO : Replace the ETACS-ECU.
Item No.
Item name
Windshield
wiper
switch
position
Normal
condition
Item 235
Front wiper
ACT
LO
ON
HI
INT
ON and
OFF
MIST
ON
Item 236
Front wiper
Lo/Hi
LO
OFF
HI
ON
INT
OFF
MIST
ON
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст