Mitsubishi Evolution X. Manual — part 254
FUEL TANK
TSB Revision
FUEL SUPPLY
13B-11
<FUEL FILLER NECK>
AC709095
20 ± 5 N·m
15 ± 3 ft-lb
20 ± 5 N·m
15 ± 3 ft-lb
20 ± 5 N·m
15 ± 3 ft-lb
1
2
3
4
5
6
7
8
9
10
12
11
AB
Removal steps
>>
A
<<
1.
Fuel filler hose connection
2.
Fuel leveling hose connection
3.
Fuel vapor hose connection
4.
Fuel vapor hose connection
5.
Rear wheel splash shield front
<MR>
6.
Fuel filler hose protector
7.
Fuel vapor tube connection
8.
Fuel leveling pipe
9.
Fuel filler neck breather hose
10. Fuel cap
11. Fuel filler neck assembly
12. Filler neck boots
Removal steps (Continued)
FUEL TANK
TSB Revision
FUEL SUPPLY
13B-12
REMOVAL SERVICE POINTS
.
<<A>> FUEL PUMP MODULE CONNECTOR/FUEL
TANK DIFFERENTIAL PRESSURE SENSOR CON-
NECTOR/FUEL MAIN PIPE/FUEL RETURN PIPE
DISCONNECTION
AC703013
AE
Floor inspection lid (LH)
1. Remove the floor inspection lid (LH).
AC709179AC
Fuel main pipe
Fuel tank differential
pressure sensor connector
Fuel tank
pump module
connector
Fuel return hose
2. Disconnect the fuel pump module connector and fuel tank
differential pressure sensor connector.
3. Disconnect the fuel return hose.
AC606017
Fuel pump module
Retainer
Flat-tip
screwdriver
Fuel main pipe
AC
4. Insert a flat-tip screwdriver [6mm (0.24 inch) wide and 1mm
(0.04 inch) thick] into the retainer of the fuel main pipe.
AC606018
Fuel pump module
Retainer
Flat-tip screwdriver
Fuel main pipe
AC
5. Turn the flat-tip screwdriver about 90 degrees to push up the
retainer, and disconnect the fuel main pipe from the fuel
pump module.
.
FUEL TANK
TSB Revision
FUEL SUPPLY
13B-13
<<B>> FUEL LEVEL SENSOR (SUB) REMOVAL
AC706390
AC
Floor inspection lid (RH)
1. Remove the floor inspection lid (RH).
AC703016 AC
Fuel level sensor
(sub) connector
2. Disconnect the fuel level sensor (sub) connector.
.
<<C>> FUEL TANK BAND/FUEL FILLER HOSE
DISCONNECTION/FUEL TANK ASSEMBLY
REMOVAL
AC703019
AC
Fuel tank
assembly
1. Support the fuel tank assembly with a transmission jack to
remove the connecting bolts of fuel tank band and the
connecting nuts of fuel tank assembly.
2. Lower the transmission jack slightly and disconnect the fuel
filler hose.
3. Tilt the fuel tank assembly, and remove the fuel tank
assembly while avoiding the rear differential carrier.
INSTALLATION SERVICE POINTS
.
>>A<< FUEL FILLER HOSE CONNECTION
AC707593AD
Hose clamp
8.5 ± 1.5 mm
(0.33 ± 0.06 in)
Connect the fuel filler hose, and tighten the bolt of hose clamp
so that the bolt tightening dimension of the hose clump
becomes 8.5
± 1.5 mm (0.33 ± 0.06 inch).
.
FUEL TANK
TSB Revision
FUEL SUPPLY
13B-14
>>B<< FUEL MAIN PIPE CONNECTION
AC606019
Retainer
Fuel main pipe
AC
1. Before the installation, push up the retainer of the fuel main
pipe.
AC606020
Retainer
Fuel main pipe
Fuel pump module
AC
2. Connect the connector of fuel main pipe to the fuel pump
module securely and push down the retainer of the
connector to lock it firmly.
3. After the installation, slightly pull the fuel main pipe to check
that it is connected securely. At this time, also check that
there is approximately 1 mm (0.04 inch) play.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст