Mitsubishi Evolution X. Manual — part 1292
HEATER CONTROL UNIT
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55-119
REPLACE THE CLEAN AIR FILTER
M1552020100289
1. Remove the glove box (Refer to GROUP 52A
− glove box,
).
2. Loosen the two lugs as shown to replace the clean air filter.
3. Install the glove box.
HEATER CONTROL UNIT
REMOVAL AND INSTALLATION
M1554014700437
AC611715AB
Pre-removal and Post-installation Operation
• Side cover, Instrument panel garnish, Upper panel
Removal and Installation (Refer to GROUP 52A, Instru-
).
• Floor console Removal and Installation (Refer to GROUP
52A, Floor console
).
AC608191
1
2
AB
Removal steps
1.
Instrument panel center lower
(Refer to GROUP 52A, Instrument
panel center panel
)
2.
Heater control
HEATER UNIT AND BLOWER ASSEMBLY
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55-120
HEATER UNIT AND BLOWER ASSEMBLY
REMOVAL AND INSTALLATION
M1552020800459
WARNING
•
Before removing the steering wheel assembly and driver's air bag module/knee air bag
module, always refer to GROUP 52B
−
Service Precautions
.)
Pre-removal and Post-installation Operation
• Refrigerant draining and Refilling (Refer to Charging and
).
• Engine coolant Draining and Refilling (Refer to GROUP
00, Engine coolant
).
• Steering Column Shaft Assembly Removal and Installa-
tion (Refer to GROUP 37, Steering Shaft
).
• Instrument Panel Removal and Installation (Refer to
GROUP 52A, Instrument Panel
• Floor console Removal and Installation (Refer to GROUP
52A, Floor console
).
HEATER UNIT AND BLOWER ASSEMBLY
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55-121
AC608202
3
3, 4
A/C compressor oil:
SUN PAG 56
-Pipe coupling
5
4
5
7
8
4.9 ± 0.9 N·m
43 ± 8 in-lb
20 ± 5 N·m
15 ± 3 ft-lb
23 ± 6 N·m
17 ± 4 ft-lb
20 ± 5 N·m
15 ± 3 ft-lb
18 ± 7 N·m
13 ± 3 ft-lb
18 ± 7 N·m
13 ± 3 ft-lb
6
N
1
2
AD
7.0 ± 3.0 N·m
62 ± 27 in-lb
11 ± 4 N·m
98 ± 35 in-lb
11 ± 4 N·m
98 ± 35 in-lb
Removal steps
1.
Dash panel heat protector
2.
Heater hose connection
<<
A
>>
3.
Flexible suction hose connection
<<
A
>>
4.
Liquid pipe B connection
5.
O-ring
6.
Front deck crossmember
7.
Drain hose
<<
B
>>
8.
Heater unit
Removal steps (Continued)
HEATER UNIT AND BLOWER ASSEMBLY
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55-122
REMOVAL SERVICE POINTS
.
<<A>> SUCTION PIPE AND LIQUID PIPE DISCON-
NECTION
CAUTION
As the compressor oil and receiver are highly moisture
absorbent, use a non-porous material to plug the hose and
nipples.
To prevent the entry of dust or other foreign bodies, plug the
dismantled hose and the nipples of the expansion valves.
.
<<B>> HEATER UNIT AND DECK
CROSSMEMBER ASSEMBLY REMOVAL
Disconnect the following connectors to gain access to the front
deck crossmember.
Connector
number
Connector name
C-23
Instrument panel wiring harness and floor
wiring harness combination
C-24
Instrument panel wiring harness and floor
wiring harness combination
C-33
Instrument panel wiring harness and console
wiring harness combination
C-41
Instrument panel wiring harness and floor
wiring harness combination
C-42
Instrument panel wiring harness and floor
wiring harness combination
C-116
Instrument panel wiring harness and front door
wiring harness (RH) combination
C-117
Instrument panel wiring harness and front door
wiring harness (RH) combination
C-128
Instrument panel wiring harness and front door
wiring harness (LH) combination
C-129
Instrument panel wiring harness and front door
wiring harness (LH) combination
C-130
Instrument panel wiring harness and front
wiring harness combination
C-131
Instrument panel wiring harness and front
wiring harness combination
C-132
Instrument panel wiring harness and front
wiring harness combination
C-133
Instrument panel wiring harness and roof wiring
harness combination
AC708950
C-131
BM
C-130
C-42
C-41
C-129
C-128
C-132
C-133
AC708951
C-24
C-23
BZ
C-34
C-117
C-116
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст