Mitsubishi Evolution X. Manual — part 448
DIAGNOSIS <TC-SST>
TSB Revision
TWIN CLUTCH- SPORTRONIC SHIFT TRANSMISSION (TC-SST)
22C-249
STEP 2. Check whether the DTC is reset.
Q: Is DTC No. P2721 set?
YES : Replace the TC-SST assembly. (Refer to
NO : Intermittent malfunction. (Refer to GROUP 00
− How
to Cope with Intermittent Malfunction
.)
DTC P2727: Clutch/Shift Pressure Solenoid 2 System (Open circuit)
CAUTION
• If there is any problem in the CAN bus lines,
an incorrect diagnostic trouble code may be
set. Prior to this diagnosis, diagnose the CAN
bus lines.
• Whenever the ECU is replaced, ensure that
the CAN bus lines are normal.
.
DIAGNOSTIC FUNCTION
TC-SST-ECU checks that the clutch/shift pressure
solenoid 2 circuit is normal.
.
DESCRIPTIONS OF MONITOR METHODS
The clutch/shift pressure solenoid 2 circuit is deter-
mined to be open.
.
MONITOR EXECUTION
• Continuous
.
MONITOR EXECUTION CONDITIONS
(OTHER MONITOR AND SENSOR)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• P0846: Clutch 2 pressure sensor system (Poor
performance)
• P0847: Clutch 2 pressure sensor system (Output
low range out)
• P0848: Clutch 2 pressure sensor system (Output
high range out)
• P2809: Clutch/shift switching solenoid 2, spool
stuck
• P2812: Clutch/shift switching solenoid 2 system
(Open circuit)
• P2814: Clutch/shift switching solenoid 2 system
(Short to ground)
• P2815: Clutch/shift switching solenoid 2 system
(Short to power supply)
• P181B: Clutch 1 (Pressure low range out)
• P181C: Clutch 1 (Pressure high range out)
• P1859: Disengagement too late with clutch 1
• P181E: Clutch 2 (Pressure low range out)
• P181F: Clutch 2 (Pressure high range out)
• P185B: Disengagement too late with clutch 2
Sensor (The sensor below is determined to be
normal)
• Clutch 2 pressure sensor
• Clutch/shift switching solenoid 2
.
DIAGNOSIS <TC-SST>
TSB Revision
TWIN CLUTCH- SPORTRONIC SHIFT TRANSMISSION (TC-SST)
22C-250
LOGIC FLOW CHARTS (Monitor Sequence)
.
DTC SET CONDITIONS
Check Conditions
• Voltage of battery: 8 V or more.
• Voltage of battery: 16.5 V or less.
JUDGMENT CRITERIA
• FET (Field Effect Transistor) output: 1 V or more.
(400 millisecond)
.
OBD-II DRIVE CYCLE PATTERN
The FET channel output remains 1 V or less for 400
milliseconds.
.
PROBABLE CAUSES
• Malfunction of TC-SST-ECU
DIAGNOSTIC PROCEDURE
STEP 1. Scan tool CAN bus diagnostics
Using scan tool MB991958, diagnose the CAN bus lines.
Q: Is the check result normal?
YES : Go to Step 2.
NO : Repair the CAN bus lines. (Refer to GROUP 54C
−
Troubleshooting
.) After repairing the CAN
bus line, go to Step 2.
STEP 2. Check whether the DTC is reset.
Q: Is DTC No. P2727 set?
YES : Replace the TC-SST assembly. (Refer to
NO : Intermittent malfunction. (Refer to GROUP 00
− How
to Cope with Intermittent Malfunction
.)
AC710656
START
No
Yes
Good
Malfunction
END
Monitoring condition met
Continuous failure
for 400 msec
No
Yes
No
Yes
FET* output > 1 V
*FET : Field Effect Transistor
DIAGNOSIS <TC-SST>
TSB Revision
TWIN CLUTCH- SPORTRONIC SHIFT TRANSMISSION (TC-SST)
22C-251
DTC P2728: Clutch/Shift Pressure Solenoid 2 System (Overcurrent)
CAUTION
• If there is any problem in the CAN bus lines,
an incorrect diagnostic trouble code may be
set. Prior to this diagnosis, diagnose the CAN
bus lines.
• Whenever the ECU is replaced, ensure that
the CAN bus lines are normal.
.
DIAGNOSTIC FUNCTION
TC-SST-ECU checks that the clutch/shift pressure
solenoid 2 circuit is normal.
.
DESCRIPTIONS OF MONITOR METHODS
The supply current to the clutch/shift pressure sole-
noid 2 is determined to be overcurrent.
.
MONITOR EXECUTION
• Continuous
.
MONITOR EXECUTION CONDITIONS
(OTHER MONITOR AND SENSOR)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• P0846: Clutch 2 pressure sensor system (Poor
performance)
• P0847: Clutch 2 pressure sensor system (Output
low range out)
• P0848: Clutch 2 pressure sensor system (Output
high range out)
• P2809: Clutch/shift switching solenoid 2, spool
stuck
• P2812: Clutch/shift switching solenoid 2 system
(Open circuit)
• P2814: Clutch/shift switching solenoid 2 system
(Short to ground)
• P2815: Clutch/shift switching solenoid 2 system
(Short to power supply)
• P181B: Clutch 1 (Pressure low range out)
• P181C: Clutch 1 (Pressure high range out)
• P1859: Disengagement too late with clutch 1
• P181E: Clutch 2 (Pressure low range out)
• P181F: Clutch 2 (Pressure high range out)
• P185B: Disengagement too late with clutch 2
Sensor (The sensor below is determined to be
normal)
• Clutch 2 pressure sensor
• Clutch/shift switching solenoid 2
.
DIAGNOSIS <TC-SST>
TSB Revision
TWIN CLUTCH- SPORTRONIC SHIFT TRANSMISSION (TC-SST)
22C-252
LOGIC FLOW CHARTS (Monitor Sequence)
.
DTC SET CONDITIONS
Check Conditions
• Voltage of battery: 8 V or more.
• Voltage of battery: 16.5 V or less.
• Engine speed: 500 r/min or more.
• Time since above engine condition: 400 millisec-
ond or more.
JUDGMENT CRITERIA
• FET (Field Effect Transistor) current: 3.5 A or
more, and FET (Field Effect Transistor) output:
100 mV or less. (300 millisecond)
.
OBD-II DRIVE CYCLE PATTERN
The status with the current of the FET channel shunt
3.5 A or less and with the FET channel output 100
mV or more continues for 300 milliseconds.
.
PROBABLE CAUSES
• Malfunction of TC-SST-ECU
AC710657
START
No
Yes
Good
Malfunction
END
Monitoring condition met
Continuous failure
for 300 msec
No
Yes
No
Yes
Yes
FET* output < 100 mV
FET* current > 3.5 A
No
*FET : Field Effect Transistor
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст