Mitsubishi Evolution X. Manual — part 915
IGNITION SWITCH
TSB Revision
CHASSIS ELECTRICAL
54A-21
REMOVAL SERVICE POINT
.
<<A>> STEERING LOCK CYLINDER REMOVAL
<VEHICLES WITH WCM>
1. Insert the key into the steering lock cylinder, and turn the
ignition key to the ACC position.
2. With using a cross-headed screw driver (small) or similar
items to press in the lock pin, remove the ignition key, and
then remove the steering lock cylinder.
INSTALLATION SERVICE POINT
.
>>A<< WIRELESS CONTROL MODULE (WCM)
<VEHICLES WITH WCM>/RECEIVER ANTENNA
MODULE <VEHICLES WITH KOS> INSTALLATION
Check that the top claw of receiver antenna module is fixed
securely to the boss of steering lock and the antenna is not
floated on the key cylinder.
5.
Ignition switch
6.
Key reminder switch
>>
A
<<
7.
Wireless control module (WCM)
<Vehicles with WCM>/receiver
antenna module <Vehicles with
KOS>
8.
Paddle shift assembly <Vehicles
with WCM and paddle shift>
9.
Column switch assembly <Vehicles
with WCM>
<
<
A
>
>
10. Steering lock cylinder <Vehicles
with WCM>
Removal Steps (Continued)
AC604821 AC
Lock pin
IGNITION SWITCH
TSB Revision
CHASSIS ELECTRICAL
54A-22
INSPECTION
IGNITION SWITCH CONTINUITY CHECK
M1541200400095
With the ignition switch mounted to the vehicle, disconnect and
check the ignition switch connection connector.
KEY REMINDER SWITCH INSPECTION
M1541200500092
With the key reminder switch mounted to the vehicle, discon-
nect the key reminder switch connection connector, and then
perform the continuity check.
Ignition key
position
Terminal number
Normal condition
LOCK
1
− 2, 1 − 4, 1 − 5, 1 − 6 No continuity
ACC
1
− 6
Continuity exists
(2 ohms or less)
ON
1
− 2 − 4 − 6
Continuity exists
(2 ohms or less)
START
1
− 2 − 5
Continuity exists
(2 ohms or less)
AC506506AB
Column switch
Key status
Terminal number
Normal condition
Key removed
2
− 3
Continuity exists
(2 ohms or less)
Key inserted
2
− 3
No continuity
AC506506AC
Column switch
COMBINATION METER
TSB Revision
CHASSIS ELECTRICAL
54A-23
COMBINATION METER
SERVICE SPECIFICATIONS
M1540200200407
Item
Standard Value
Speedometer indication tolerance {mph (km/h)}
<Except vehicles for CANADA>
10 (16)
8.5
− 11.5 (13.6 − 18.4)
25 (40)
23.5
− 26.5 (37.6 − 42.4)
50 (80)
48.5
− 51.5 (77.6 − 82.4)
75 (120)
73.5
− 76.5 (117.6 − 122.4)
100 (161)
98.5
− 102.5 (158.6 − 165.0)
125 (201)
123.5
− 127.5 (198.6 − 205.0)
150 (241)
148.5
− 153.5 (239.0 − 247.0)
175 (282)
173.5
− 179.0 (279.2 − 288.0)
Speedometer indication tolerance {km/h (mph)}
<Vehicles for CANADA>
20 (12.4)
19
− 24 (11.8 − 14.9)
40 (24.8)
40
− 44 (24.8 − 27.3)
80 (49.7)
80
− 85 (49.7 − 52.8)
120 (74.6)
120.5
− 125.5 (74.9 − 78.0)
160 (99.4)
160.5
− 165.5 (99.7 − 102.8)
200 (124.3)
200.5
− 207.0 (124.6 − 128.6)
240 (149.1)
240.5
− 247.0 (149.4 − 153.5)
280 (174.0)
280.5
− 289.0 (174.3 − 179.6)
Tachometer indication tolerance (r/min)
(The value in parentheses is a reference value.)
600
550
− 650
(2,000)
(1,950
− 2,050)
3,000
2,950
− 3,050
(4,000)
(3,950
− 4,050)
5,000
4,950
− 5,050
6,000
5,950
− 6,050
(7,000)
(6,950
− 7,050)
(8,000)
(7,950
− 8,050)
Fuel level sensor resistance (ohms)
main
Stopper position "F"
6.5
± 1.0
Stopper position "E"
41.9
± 1.0
sub
Stopper position "F"
6.5
± 1.0
Stopper position "E"
78.1
± 1.0
Fuel level sensor float height {mm (in)} main
Stopper position "F"
140.9 (5.5)
Stopper position "E"
39.1 (1.5)
sub
Stopper position "F"
14.2
± 3.0 (0.5 ± 0.1)
Stopper position "E"
179.3
± 3.0 (7.0 ± 0.1)
COMBINATION METER
TSB Revision
CHASSIS ELECTRICAL
54A-24
SPECIAL TOOLS
M1540200300147
Tool
Tool number and
name
Supersession
Application
MB991958
a. MB991824
b. MB991827
c. MB991910
d. MB991911
e. MB991914
f. MB991825
g. MB991826
M.U.T.-III
sub-assembly
a. Vehicle
communication
interface (V.C.I.)
b. M.U.T.-III USB
cable
c. M.U.T.-III main
harness A
(Vehicles with
CAN
communication
system)
d. M.U.T.-III main
harness B
(Vehicles
without CAN
communication
system)
e. M.U.T.-III main
harness C (for
Daimler
Chrysler
models only)
f. M.U.T.-III
measurement
adapter
g. M.U.T.-III trigger
harness
MB991824-KIT
NOTE: G:
MB991826
M.U.T.-III Trigger
Harness is not
necessary when
pushing V.C.I.
ENTER key.
CAUTION
M.U.T.-III main harness A
(MB991910) should be used.
M.U.T.-III main harness B and C
should not be used for this
vehicle.
DTC, data list and actuator test
check.
MB991910
MB991826
MB991958
MB991911
MB991914
MB991824
MB991827
MB991825
DO NOT USE
a
b
c
d
e
f
g
DO NOT USE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст