Mitsubishi Evolution X. Manual — part 384
TRANSAXLE CASE
TSB Revision
MANUAL TRANSAXLE OVERHAUL
22B-49
DISASSEMBLY SERVICE POINTS
.
<<A>> OIL GUIDE REMOVAL
AK703404AC
MB991946
Using special tool, MB991946, remove the oil guides from the
transaxle case.
ASSEMBLY SERVICE POINTS
.
>>A<< AIR BREATHER INSTALLATION
AK703373
AC
Identification mark
Clutch housing
side
1. Apply specified sealant to the periphery of the air breather
insertion part.
Specified sealant:
Three bond 1501 or equivalemt
2. Install the air breather to the transaxle case in accordance
with the illustrated identification mark.
.
>>B<< STEEL BALL INSTALLATION
AK703371AC
Steel ball
1. Apply specified sealant to the periphery of the transaxle
case where the steel ball is installed, then install the steel
ball onto the transaxle case.
Specified sealant:
3M
™STUD Locking No.4710 or equivalent
AK703372
AC
MB990883
2. Using special tool, MB990883, install the steel ball.
.
TRANSAXLE CASE
TSB Revision
MANUAL TRANSAXLE OVERHAUL
22B-50
>>C<< OIL SEAL INSTALLATION
AK703406AC
MB991115
MB990938
1. Using the special tools, MB991115 and MB990938,
indicated below, install the oil seal to the transaxle case.
AK703405 AC
2. Apply specified transaxle oil to the oil seal lip area.
Specified transaxle oil:
Mitsubishi Genuine DiaQueen New Multi Gear Oil SAE
75W-80 (GL-3)
.
>>D<< SLIDE BALL BEARING (FOR CONTROL
SHAFT) INSTALLATION
CAUTION
• Normally, it is not necessary to disassemble the slide
ball bearing. Install it only when the transaxle case is
replaced with a new one.
•
AK703370
AC
MB990883
Install the bearing with the stamped mark facing
upward.
Using special tool, MB990883, install the slide ball bearing (for
control shaft) to the new transaxle case.
.
TRANSAXLE CASE
TSB Revision
MANUAL TRANSAXLE OVERHAUL
22B-51
>>E<< SLIDE BALL BEARING (FOR SHIFT RAIL)
INSTALLATION
CAUTION
• Normally, it is not necessary to disassemble the slide
ball bearing. Install it only when the transaxle case is
replaced with a new one.
•
AK703338
AC
MB990883
Install the bearing with the stamped mark facing
upward.
Using special tool, MB990883, install the slide ball bearing (ror
shift rail) to the new transaxle case.
.
>>F<< OIL GUIDE A INSTALLATION
CAUTION
Normally, it is not necessary to disassemble the oil guide
A. Install the oil guide only when the transaxle case is
replaced with a new one.
AK703339
Install the oil guide A to the new transaxle case. Stake at the
illustrated point to secure the oil guide in position.
.
>>G<< OIL TANK COVER INSTALLATION
CAUTION
Normally, it is not necessary to disassemble the oil tank
cover. Install the cover only when the transaxle case is
replaced with a new one.
AK703340
Install the oil tank cover onto the new transaxle case. Stake at
the illustrated six points to secure the cover in position.
TRANSAXLE CASE
TSB Revision
MANUAL TRANSAXLE OVERHAUL
22B-52
.
>>H<< OIL GUIDE INSTALLATION
CAUTION
Install the oil guide squarely.
AK703368
AC
MD999547
<Input shaft side>
AK703369
AC
MD999547
<Output shaft side>
Using special tool, MD999547, drive the oil guide all the way
into place to the end face of the transaxle case.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст