Mitsubishi Evolution X. Manual — part 1156
TROUBLESHOOTING
TSB Revision
LOCAL INTERCONNECT NETWORK (LIN)
54B-17
Recheck for diagnostic trouble code.
Check again if the DTC is set to the ETACS-ECU.
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958. Refer to "How to connect the
Scan Tool (M.U.T.-III)
(2) Erase the DTC.
(3) Turn the ignition switch to the "ON" position.
(4) Check if the DTC is set.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES : Replace the lighting switch.
NO : A poor connection, open circuit, or other intermittent
malfunctions in the LIN bus lines between the column
switch and the ETACS-ECU (Refer to GROUP 00,
How to Cope with Intermittent Malfunction
DTC U150C: P/W SW (DR) checksum error
.
TROUBLE JUDGMENT
The ETACS-ECU will set DTC U150C when abnor-
mal signals are received from the power window
main switch.
.
TROUBLESHOOTING HINTS
• The power window main switch may be defective.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicles Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
TROUBLESHOOTING
TSB Revision
LOCAL INTERCONNECT NETWORK (LIN)
54B-18
Recheck for diagnostic trouble code.
Check again if the DTC is set to the ETACS-ECU.
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958. Refer to "How to connect the
Scan Tool (M.U.T.-III)
(2) Erase the DTC.
(3) Turn the ignition switch to the "ON" position.
(4) Check if the DTC is set.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES : Replace the power window main switch.
NO : A poor connection, open circuit, or other intermittent
malfunctions in the LIN bus lines between the power
window main switch and the ETACS-ECU (Refer to
GROUP 00, How to Cope with Intermittent
Malfunction
).
DTC U1511: Sunroof checksum error <Vehicles with sunroof>
.
TROUBLE JUDGMENT
The ETACS-ECU will set DTC U1511 when abnor-
mal signals are received from the sunroof motor
assembly (sunroof-ECU).
.
TROUBLESHOOTING HINTS
• The sunroof motor assembly may be defective.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicles Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
TROUBLESHOOTING
TSB Revision
LOCAL INTERCONNECT NETWORK (LIN)
54B-19
Recheck for diagnostic trouble code.
Check again if the DTC is set to the ETACS-ECU.
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958. Refer to "How to connect the
Scan Tool (M.U.T.-III)
(2) Erase the DTC.
(3) Turn the ignition switch to the "ON" position.
(4) Check if the DTC is set.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES : Replace the sunroof motor assembly.
NO : A poor connection, open circuit, or other intermittent
malfunctions in the LIN bus lines between the sunroof
motor assembly and the ETACS-ECU (Refer to
GROUP 00, How to Cope with Intermittent
Malfunction
).
DTC U1512: Rain light sensor checksum error <Vehicles with auto light function>
.
TROUBLE JUDGMENT
The ETACS-ECU will set DTC U1512 when abnor-
mal signals are received from the lighting control
sensor.
.
TROUBLESHOOTING HINTS
• The lighting control sensor may be defective.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicles Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
TROUBLESHOOTING
TSB Revision
LOCAL INTERCONNECT NETWORK (LIN)
54B-20
Recheck for diagnostic trouble code.
Check again if the DTC is set to the ETACS-ECU.
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958. Refer to "How to connect the
Scan Tool (M.U.T.-III)
(2) Erase the DTC.
(3) Turn the ignition switch to the "ON" position.
(4) Check if the DTC is set.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES : Replace the lighting control sensor.
NO : A poor connection, open circuit, or other intermittent
malfunctions in the LIN bus lines between the lighting
control sensor and the ETACS-ECU (Refer to
GROUP 00, How to Cope with Intermittent
Malfunction
).
DTC U1514: Bit error (LIN)
.
TROUBLE JUDGMENT
The ETACS-ECU receives and sends data simulta-
neously. If the data contains a fault, the ETACS-ECU
will set DTC U1514.
.
TROUBLESHOOTING HINTS
• The slave ECU may be defective.
• The ETACS-ECU may be defective.
• Electrical noise generated in the LIN bus lines
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicles Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст