Mitsubishi Evolution X. Manual — part 217
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-37
STEP 1. Using scan tool MB991958, check for MFI system
DTC.
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector
(Refer to
).
(2) Turn the ignition switch to the "ON" position.
(3) Check for MFI system DTC (Refer to GROUP 13A, MFI
Diagnosis
− Diagnostic Function
).
(4) Turn the ignition switch to the "LOCK" (OFF) position.
(5) Disconnect scan tool MB991958.
Q: Is any DTC set?
YES : Diagnose the MFI system (Refer to GROUP 13A, MFI
Diagnosis
− Diagnostic Trouble Code Chart
). Then go to Step 3.
NO : Go to Step 2.
STEP 2. Read the cruise control system DTC.
(1) Disconnect the negative (
−) battery terminal, to erase the
DTC of the cruise control system.
(2) Connect the negative (
−) battery terminal.
(3) Turn the ignition switch to the "ON" position, and press the
"ON/OFF" switch to turn the cruise control system to ON
(turn on the "CRUISE" indicator light).
(4) After turning the cruise control system to ON, when 2
minutes or more has elapsed without operating the cruise
control switches, read the DTC of the cruise control system
(Refer to
).
Q: Is DTC 23 set?
YES : Replace the ECM [Refer to GROUP 13A, Engine
]. When the ECM is
replaced, register the encrypted code (Refer to
GROUP 42C, Diagnosis
− ID Code Registration
Judgment Table
NO : It can be assumed that this malfunction is intermittent
(Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunction
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-38
STEP 3. Read the cruise control system DTC.
(1) Disconnect the negative (
−) battery terminal, to erase the
DTC of the cruise control system.
(2) Connect the negative (
−) battery terminal.
(3) Turn the ignition switch to the "ON" position, and press the
"ON/OFF" switch to turn the cruise control system to ON
(turn on the "CRUISE" indicator light).
(4) After turning the cruise control system to ON, when 2
minutes or more has elapsed without operating the cruise
control switches, read the DTC of the cruise control system
(Refer to
).
Q: Is DTC 23 set?
YES : Return to Step 1.
NO : The procedure is complete.
SYMPTOM CHART
M1172002301091
Symptom
Inspection
procedure
number
Reference page
Communication with
scan tool is not
possible
Communication with the ECM only is
impossible
−
GROUP 13A, MFI
Diagnosis,
Symptom
Procedures
−
Inspection
Procedure 1
Cruise control is not
cancelled.
When brake pedal is depressed
1
When clutch pedal is depressed <M/T>
2
When shift lever is moved to "N" position
<TC-SST>
3
When "CANCEL" switch is turned ON
4
Cruise control cannot be set ("COAST/SET" or "ACC/RES" switch
operation is not available).
5
Hunting (repeated acceleration and deceleration) occurs at the
set vehicle speed.
6
When "ON/OFF" switch is turned ON, "CRUISE" indicator light
inside combination meter does not illuminate. (However, cruise
control system is normal).
7
SYMPTOM PROCEDURES
INSPECTION PROCEDURE 1: When the Brake Pedal is Depressed, Cruise Control System is not
Cancelled.
.
COMMENT
• Malfunction of CAN bus line.
• The stoplight switch circuit is suspected.
.
TROUBLESHOOTING HINTS (THE MOST
LIKELY CAUSES FOR THIS CASE:)
• Malfunction of CAN bus system.
• Damaged harness or connector.
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-39
• Malfunction of the stoplight switch.
• Malfunction of the ETACS-ECU.
• Malfunction of the ECM.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A
• MB991223: Harness Set
• MB992006: Extra Fine Probe
CAUTION
• If there is any problem in the CAN bus lines, an incor-
rect DTC may be set. Prior to this diagnosis, diagnose
the CAN bus lines.
• Whenever the ECM is replaced, ensure that the CAN
bus lines are normal.
STEP 1. Using scan tool MB991958, diagnose the CAN bus
line.
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector
(Refer to
).
(2) Turn the ignition switch to the "ON" position.
(3) Diagnose the CAN bus line (Refer to
(4) Turn the ignition switch to the "LOCK" (OFF) position.
(5) Disconnect scan tool MB991958.
Q: Is the check result satisfactory?
YES : Go to Step 2
NO : Repair the CAN bus lines (Refer to GROUP 54C,
Diagnosis
− Can Bus Diagnostic Chart
Then go to Step 4.
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-40
STEP 2. Using scan tool MB991958, check data list item 74:
Brake light switch and item 89: Normally closed brake
switch.
(1) Connect scan tool MB991958 to the data link connector
(Refer to
).
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to data reading mode for cruise
control system (Refer to
).
• Item 74: Brake light switch.
• When the brake pedal is depressed, the display on
scan tool MB991958 should be "ON".
• When the brake pedal is released, the display on
scan tool MB991958 should be "OFF".
• Item 89: Normally closed brake switch.
• When the brake pedal is depressed, the display on
scan tool MB991958 should be "ON".
• When the brake pedal is released, the display on
scan tool MB991958 should be "OFF".
(4) Turn the ignition switch to the "LOCK" (OFF) position.
(5) Disconnect scan tool MB991958.
Q: Is the switch operating properly?
YES : Go to Step 3
NO : Refer to
, Diagnostic Trouble Code
Procedures
− DTC 22: Stoplight Switch System. Then
go to Step 4.
STEP 3. Check the symptoms.
Q: When the brake pedal is depressed, cruise control
system is cancelled?
YES : It can be assumed that this malfunction is intermittent
(Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunction
NO : Replace the ECM [Refer to GROUP 13A, Engine
]. When the ECM is
replaced, register the encrypted code (Refer to
GROUP 42C, Diagnosis
− ID Code Registration
Judgment Table
STEP 4. Check the symptoms.
Q: When the brake pedal is depressed, cruise control
system is cancelled?
YES : The procedure is complete.
NO : Return to Step 1.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст