Mitsubishi Evolution X. Manual — part 733
ON-VEHICLE SERVICE
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-379
(5) The execution check of the zero calibration.
(6) The zero calibration has been completed when the
screen as shown in the illustration is displayed. The OK
button is pushed and it progresses to the next.
(7) The start of 66 lbs system test.
(8) The execution check of the 66 lbs system test.
(9) The 66 lbs system test has been completed when the
screen as shown in the illustration is displayed. The OK
button is pushed and it progresses to the next.
(10)The start of 0 lbs system test.
(11)The execution check of the 0 lbs system test.
AC609604
AB
Zero-calibration
Completed.
Go on to the 66lbs System Test.
MUT-lll-- Web Web Page Dialog
AC710647
AB
MUT-lll-- Web Web Page Dialog
66lbs System Test
Do you want to start?
AC710648
AB
MUT-lll-- Web Web Page Dialog
66lbs System Test
Test passed.
Go on to the 0kg System Test.
AC710649
AB
MUT-lll-- Web Web Page Dialog
0lbs System Test
Do you want to start?
AC710650
AB
FRONT IMPACT SENSORS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-380
(12)The 0 lbs system test has been completed when the
screen as shown in the illustration is displayed.
FRONT IMPACT SENSORS
REMOVAL AND INSTALLATION
M1524001501198
WARNING
•
Never repair or disassemble the front impact sensor. If faulty, replace it.
•
Handle the front impact sensors very carefully, taking care not to drop them. They must
be replaced if they are dropped.
•
Replace the sensors with new ones after the air bag has deployed.
NOTE: The figure indicates the left front impact sen-
sor. The right impact sensor is symmetrical to this.
MUT-lll-- Web Web Page Dialog
0lbs System Test
Test passed.
All procedure is completed.
Please erase stored DTCS set during
the test in OCM and SRS-AIR BAG.
AC710651
AB
Pre-removal Operation
• Turn the ignition key to the "LOCK" (OFF) position.
AC709459 AB
1
12 ± 1 N·m
102 ± 13 in-lb
2
3
4
Headlight
Removal steps
<<
A
>>
1.
Negative (
−) battery cable
•
Headlight support panel cover
(Refer to Group 51, Front Bumper
Assembly and Radiator Grille
).
2.
Air bag sensor bracket
<<
B
>>
3.
Front impact sensor connector
4.
Front impact sensor
Installation steps
>>
A
<<
•
Pre-installation inspection
>>
B
<<
4.
Front impact sensor
3.
Front impact sensor connector
2.
Air bag sensor bracket
•
Headlight support panel cover
(Refer to Group 51, Front Bumper
Assembly and Radiator Grille
).
1.
Negative(
−) battery cable
>>
C
•
Post-installation inspection
Installation steps (Continued)
FRONT IMPACT SENSORS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-381
REMOVAL SERVICE POINTS
.
<<A>> NEGATIVE (
−) BATTERY CABLE DISCON-
NECTION
DANGER
Wait at least 60 seconds after disconnecting the bat-
tery cable before doing any further work (Refer to
).
WARNING
Battery posts, terminals and related accessories con-
tain lead and lead compounds. WASH HANDS AFTER
HANDLING.
Disconnect the negative (
−) battery cable from the battery and
tape the terminal to prevent accidental connection and air
bag(s) deployment.
.
<<B>> FRONT IMPACT SENSOR CONNECTOR
REMOVAL
Press the connector lock of the harness-side connector of the
front impact sensor to release the lock. Then, remove the har-
ness-side connector by pulling it in the direction of the arrow.
ACX00583
Insulating tape
Battery cable
Battery
AF
AC700462
AC707048
AC707283
AC
Connector lock
Front impact sensor
Harness side
connector
Section A - A
A
A
FRONT IMPACT SENSORS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-382
INSTALLATION SERVICE POINTS
.
>>A<< PRE-INSTALLATION INSPECTION
When installing the new front impact sensor, refer to "INSPEC-
TION."
.
>>B<< FRONT IMPACT SENSOR INSTALLATION
WARNING
The SRS may not activate properly if a front impact
sensor is not installed properly, which could result in
serious injury or death to the vehicle's driver.
1. Securely connect the connector.
2. Position the front impact sensor facing toward the front of
the vehicle as indicated by the arrow on the label, and install
it securely.
.
>>C<< POST-INSTALLATION INSPECTION
1. Reconnect the negative (
−) battery cable.
2. Turn the ignition key to "ON" position.
3. Does the "SRS" warning light illuminate for approximately
seven seconds, and then go out?
4. If yes, the SRS system is functioning properly.
If not, consult page
.
INSPECTION
M1524001600761
WARNING
If a dent, crack, deformation or rust is
detected, replace with a new sensor.
NOTE: For checking of the front impact sensor other
than described below, refer to the section concerning
SRS diagnosis (Refer to
1. Check the front impact sensor and bracket for
dents, cracks or deformation.
2. Check the connector for damage, and terminals
for deformation.
3. Check that there is no bending or corrosion in the
radiator support panel.
AC709154
SRS warning light
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст