Mitsubishi Evolution X. Manual — part 319
TOWING AND HOISTING
TSB Revision
GENERAL
00-51
POST TYPE
Special care should be taken when raising the vehicle on a
frame contact type hoist. The hoist must be equipped with the
proper adapters in order to support the vehicle at the proper
locations.
CAUTION
When service procedures require removing rear suspen-
sion, fuel tank and spare tire, place additional weight on
the rear end of vehicle, or anchor vehicle to hoist to pre-
vent tipping when the location of the center of gravity
changes.
AC709514
Notch
Notch
AB
GENERAL DATA AND SPECIFICATIONS
TSB Revision
GENERAL
00-52
GENERAL DATA AND SPECIFICATIONS
M1001000902565
.
VEHICLES FOR USA
.
AC710509 AC
9
3
1
2
5
4
6
7
8
Item
CZ4AS
NGFZL2M
MGFZL2M
MPFZL2M
Vehicle
dimension mm
(in)
Overall width
1
1,810 (71.3)
1,810 (71.3)
1,810 (71.3)
Tread-front
2
1,545 (60.8)
1,545 (60.8)
1,545 (60.8)
Overall length
3
4,495 (177.0)
4,495 (177.0)
4,495 (177.0)
Overhang-front
4
910 (35.8)
910 (35.8)
910 (35.8)
Wheelbase
5
2,650 (104.3)
2,650 (104.3)
2,650 (104.3)
Overhang-rear
6
935 (36.8)
935 (36.8)
935 (36.8)
Ground clearance
7
135 (5.3)
135 (5.3)
135 (5.3)
Overall height (unladen)
8
1,480 (58.3)
1,480 (58.3)
1,480 (58.3)
Tread-rear
9
1,545 (60.8)
1,545 (60.8)
1,545 (60.8)
Vehicle weight
kg (lb)
Curb weight
1,595 (3,517)
1,620 (3,572)
1,630 (3,594)
Gross vehicle weight rating
2,060 (4,542)
2,060 (4,542)
2,060 (4,542)
Gross axle weight rating-front
1,080 (2,381)
1,080 (2,381)
1,080 (2,381)
Gross axle weight rating-rear
1,050 (2,315)
1,050 (2,315)
1,050 (2,315)
Seating capacity
5
5
5
Engine
Model No.
4B11
4B11
4B11
Piston displacement cm
3
(cu in)
1,998 (121.9)
1,998 (121.9)
1,998 (121.9)
Maximum output kW/r/min
(HP/r/min)
217/6,500
(291/6,500)
217/6,500
(291/6,500)
217/6,500
(291/6,500)
Maximum torque N
⋅ m/r/min
(ft-lb/r/min)
407/4,000
(300/4,000)
407/4,000
(300/4,000)
407/4,000
(300/4,000)
Fuel system
Fuel supply system
MFI
MFI
MFI
Transaxle
Model No.
W5M6A
W6DGA
W6DGA
Type
5M/T
TC-SST
TC-SST
Turning radius m (ft)
5.0 (16.4)
5.0 (16.4)
5.0 (16.4)
GENERAL DATA AND SPECIFICATIONS
TSB Revision
GENERAL
00-53
VEHICLES FOR CANADA
AC710509 AC
9
3
1
2
5
4
6
7
8
Item
CY4AS
NGFL3M
MPFL3M
Vehicle
dimension mm
(in)
Overall width
1
1,810 (71.3)
1,810 (71.3)
Tread-front
2
1,545 (60.8)
1,545 (60.8)
Overall length
3
4,495 (177.0)
4,495 (177.0)
Overhang-front
4
910 (35.8)
910 (35.8)
Wheelbase
5
2,650 (104.3)
2,650 (104.3)
Overhang-rear
6
935 (36.8)
935 (36.8)
Ground clearance
7
135 (5.3)
135 (5.3)
Overall height (unladen)
8
1,480 (58.3)
1,480 (58.3)
Tread-rear
9
1,545 (60.8)
1,545 (60.8)
Vehicle weight
kg (lb)
Curb weight
1,600 (3,528)
1,635 (3,606)
Gross vehicle weight rating
2,060 (4,542)
2,060 (4,542)
Gross axle weight rating-front
1,080 (2,381)
1,080 (2,381)
Gross axle weight rating-rear
1,050 (2,315)
1,050 (2,315)
Seating capacity
5
5
Engine
Model No.
4B11
4B11
Piston displacement cm
3
(cu in)
1,998 (121.9)
1,998 (121.9)
Maximum output kW/r/min
(HP/r/min)
217/6,500 (291/6,500)
217/6,500 (291/6,500)
Maximum torque N
⋅ m/r/min
(ft-lb/r/min)
407/4,000 (300/4,000)
407/4,000 (300/4,000)
Fuel system
Fuel supply system
MFI
MFI
Transaxle
Model No.
W5M6A
W6DGA
Type
5M/T
TC-SST
Turning radius m (ft)
5.0 (16.4)
5.0 (16.4)
TIGHTENING TORQUE
TSB Revision
GENERAL
00-54
TIGHTENING TORQUE
M1001001100964
Each torque value in the table is a standard value for
tightening under the following conditions.
1. Bolts, nuts and washers are all made of steel and
plated with zinc.
2. The threads and bearing surface of bolts and
nuts are all in dry condition.
The values in the table are not applicable:
1. If toothed washers are inserted.
2. If plastic parts are fastened.
3. If bolts are tightened to plastic or die-cast
inserted nuts.
4. If self-tapping screws or self-locking nuts are
used.
STANDARD BOLT AND NUT TIGHTENING TORQUE
FLANGE BOLT AND NUT TIGHTENING TORQUE
Thread size
Standard tightening torque
Nominal bolt
diameter (mm)
Pitch
(mm)
Head mark "4"
Head mark "7"
Head mark "8"
M5
0.8
2.5
± 0.5 N⋅ m (23 ± 4
in-lb)
5.0
± 1.0 N⋅ m (44 ± 9
in-lb)
6.0
± 1.0 N⋅ m (53 ± 9
in-lb)
M6
1.0
5.0
± 1.0 N⋅ m (44 ± 9
in-lb)
8.5
± 1.5 N⋅ m (76 ± 13
in-lb)
10
± 2 N⋅ m (89 ± 17
in-lb)
M8
1.25
11
± 2 N⋅ m (98 ± 17
in-lb)
20
± 4 N⋅ m (15 ± 3 ft-lb) 24 ± 4 N⋅ m (18 ± 3 ft-lb)
M10
1.25
23
± 4 N⋅ m (17 ± 3 ft-lb) 42 ± 8 N⋅ m (31 ± 6 ft-lb) 53 ± 7 N⋅ m (39 ± 5 ft-lb)
M12
1.25
42
± 8 N⋅ m (31 ± 6 ft-lb) 80 ± 10 N⋅ m (59 ± 7
ft-lb)
93
± 12 N⋅ m (68 ± 9
ft-lb)
M14
1.5
70
± 10 N⋅ m (52 ± 7
ft-lb)
130
± 20 N⋅ m (96 ± 15
ft-lb)
150
± 20 N⋅ m (111 ± 14
ft-lb)
M16
1.5
105
± 15 N⋅ m (78 ± 11
ft-lb)
195
± 25 N⋅ m (144 ± 18
ft-lb)
230
± 30 N⋅ m (170 ± 22
ft-lb)
M18
1.5
150
± 20 N⋅ m (111 ± 14
ft-lb)
290
± 40 N⋅ m (214 ± 29
ft-lb)
335
± 45 N⋅ m (247 ± 33
ft-lb)
M20
1.5
210
± 30 N⋅ m (155 ± 22
ft-lb)
400
± 60 N⋅ m (295 ± 44
ft-lb)
465
± 65 N⋅ m (343 ± 48
ft-lb)
M22
1.5
290
± 40 N⋅ m (214 ± 29
ft-lb)
540
± 80 N⋅ m (398 ± 59
ft-lb)
630
± 90 N⋅ m (465 ± 66
ft-lb)
M24
1.5
375
± 55 N⋅ m (277 ± 40
ft-lb)
705
± 105 N⋅ m (520 ±
77 ft-lb)
820
± 120 N⋅ m (605 ±
88 ft-lb)
Thread size
Standard tightening torque
Nominal bolt
diameter (mm)
Pitch
(mm)
Head mark "4"
Head mark "7"
Head mark "8"
M6
1.0
5.0
± 1.0 N⋅ m (44 ± 9
in-lb)
10
± 2 N⋅ m (89 ± 17
in-lb)
12
± 2 N⋅ m (107 ± 17
in-lb)
M8
1.25
13
± 2 N⋅ m (111 ± 22
in-lb)
24
± 4 N⋅ m (18 ± 3 ft-lb) 28 ± 5 N⋅ m (20 ± 4 ft-lb)
M10
1.25
26
± 5 N⋅ m (19 ± 4 ft-lb) 50 ± 5 N⋅ m (37 ± 4 ft-lb) 58 ± 7 N⋅ m (43 ± 5 ft-lb)
M10
1.5
25
± 4 N⋅ m (18 ± 3 ft-lb) 46 ± 8 N⋅ m (34 ± 6 ft-lb) 55 ± 5 N⋅ m (41 ± 3 ft-lb)
M12
1.25
47
± 9 N⋅ m (35 ± 6 ft-lb) 93 ± 12 N⋅ m (68 ± 9
ft-lb)
105
± 15 N⋅ m (78 ± 11
ft-lb)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст