Mitsubishi Evolution X. Manual — part 504
DOOR
TSB Revision
BODY
42A-119
DOOR INSIDE HANDLE CHECK
M1423001500667
DOOR INSIDE HANDLE KNOB PLAY CHECK
1. Check that the door inside handle knob play meets the
standard value.
Standard value (B):
Front driver’s side: 10.0
− 23.7 mm (0.39 − 0.93 inch)
[Target value: 17.0 mm (0.67 inch)]
Except Front driver’s side: 5.0
− 18.7 mm (0.2 − 0.74
inch) [Target value: 12.0 mm (0.47 inch)]
2. Check the door inside handle and door latch assembly, and
replace them if they are out of the standard value.
DOOR INSIDE HANDLE LOCK KNOB STROKE
CHECK
1. Remove the door trim assembly (Refer to GROUP 52A
−
Door Trim
2. Check that the stroke of the door inside handle lock knob
meets the standard value.
Standard value (B): 13.7
− 15.0 mm (0.54 − 0.59 inch)
[Target value: 14.7 mm (0.58 inch)]
AC605583
A
A
B
AC
Section A – A
AC605584
A
B
AC
A
Section A – A
DOOR
TSB Revision
BODY
42A-120
3. If it is outside the standard value, adjust the stroke of the
inside handle lock knob by using the outer cable end, which
connects the inside handle lock knob to the inside lock
cable.
CONFIGURATION FUNCTION
M1429007800222
Using the ETACS system of scan tool MB991958,
the following function can be programmed. The pro-
grammed information is held even when the battery
is disconnected.
AC605585 AC
Clip
Outer cable end
Inside lock
cable
Door inside handle
Adjustment
item (scan tool
MB991958
M.U.T.-III
display)
Adjustment item
Adjusting contents
(scan tool MB991958
display)
Adjusting contents
Auto door
unlock by P
position
Auto door unlock by
P position function
<Vehicles with
TC-SST>
Disable
No function (default)
Always enabled
Always with function
DOOR
TSB Revision
BODY
42A-121
DOOR ASSEMBLY
REMOVAL AND INSTALLATION
M1423002200885
Post-installation Operation
• Door Fit Adjustment (Refer to
).
AC607387
8
9
2
1
6
5
3
4
7
AE
26 ± 6 N·m
19 ± 5 ft-lb
26 ± 6 N·m
19 ± 5 ft-lb
25 ± 4 N·m
19 ± 3 ft-lb
20 ± 5 N·m
15 ± 3 ft-lb
5.0 ± 1.0 N·m
44 ± 9 in-lb
<Front door>
5, 6
Front door assembly removal
steps
•
Cowl side trim (Refer to GROUP
52A, Trim
.)
•
Bottom cover assembly
<Passenger’s side> (Refer to
GROUP 52A, Glove Box
.)
1.
Wiring harness connector
connection
2.
Door check connecting bolt
3.
Front door assembly
Front door hinge removal steps
3.
Front door assembly
4.
Fender protector rear
5
Front door upper hinge
6.
Front door lower hinge
Striker removal steps
>>A<<
7.
Striker
Damper removal
8.
Damper
Door switch removal
•
Center piller trim lower (Refer to
GROUP 52A - Interior Trim
9.
Door switch
DOOR
TSB Revision
BODY
42A-122
INSTALLATION SERVICE POINT
.
>>A<< STRIKER INSTALLATION
Align the center of the striker and latch within
±1.5 mm (0.06
inch), and install.
AC607388
7
5
2
3
1
6
8
AC
<Rear door>
26 ± 6 N·m
19 ± 5 ft-lb
26 ± 6 N·m
19 ± 5 ft-lb
25 ± 4 N·m
19 ± 3 ft-lb
18 ± 7 N·m
13 ± 5 ft-lb
18 ± 7 N·m
13 ± 5 ft-lb
20 ± 5 N·m
15 ± 3 ft-lb
5.0 ± 1.0 N·m
44 ± 9 in-lb
3
2
4, 5
4
Door assembly removal steps
1.
Wiring harness connector
connection
2.
Door check connecting bolt
3.
Door assembly
Rear door hinge removal steps
•
Center pillar trim lower (Refer to
GROUP 52A, Trim
.)
3.
Door assembly
4.
Rear door upper hinge
5.
Rear door lower hinge
Striker removal
>>A<<
6.
Striker
Damper removal
7.
Damper
Door switch removal steps
8.
Door switch
Rear door hinge removal steps
AC006126AC
Striker center
Striker
Latch center
Latch
+1.5 mm
(0.06 in)
-1.5 mm
(0.06 in)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст