Mitsubishi Evolution X. Manual — part 604
DIAGNOSIS
TSB Revision
WIRELESS CONTROL MODULE (WCM)
42C-33
STEP 5. Recheck for diagnostic trouble code.
Check again if the DTC is set to the WCM.
(1) Erase the DTC.
(2) Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(3) Check if DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES : Replace WCM and register the ID codes (Refer to
NO : The trouble can be an intermittent malfunction (Refer
to GROUP 00
− How to use
Troubleshooting/inspection Service Points
− How to
Cope with Intermittent Malfunction
DTC B2204: Coding data mismatch
CAUTION
• When DTC B2204 is set, be sure to diagnose
the CAN bus line.
• When replacing the ECU, always check that
the communication circuit is normal.
.
DTC SET CONDITION
If the vehicle information data transmitted from the
ETACS-ECU via the CAN bus lines is different from
that registered in the WCM, the WCM sets the DTC
No. B2204.
.
TECHNICAL DESCRIPTION (COMMENT)
WCM determines that the abnormality is present
when the vehicle information registered in it does not
match the vehicle information data.
.
TROUBLESHOOTING HINTS
• Malfunction of WCM
• Malfunction of ETACS-ECU
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A
DIAGNOSIS
TSB Revision
WIRELESS CONTROL MODULE (WCM)
42C-34
STEP 1. Using scan tool MB991958, diagnose the CAN bus
line.
CAUTION
To prevent damage to scan tool (MB991958), always turn
the ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool (MB991958).
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Diagnose the CAN bus line.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the CAN bus line found to be normal?
YES : Go to Step 2.
NO : Repair the CAN bus line (Refer to GROUP 54C,
).
STEP 2. Using scan tool MB991958, read the ETACS-ECU
diagnostic trouble code
Check again if the DTC is set to the ETACS-ECU.
Q: Is the DTC set?
YES : Troubleshoot the ETACS (Refer to GROUP 54A
−
ETACS, Diagnosis
).
NO : Go to Step 3.
STEP 3. Recheck for diagnostic trouble code.
Check again if the DTC is set to the WCM.
(1) Erase the DTC.
(2) Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(3) Check if DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES : Replace WCM and register the ID codes (Refer to
NO : The trouble can be an intermittent malfunction (Refer
to GROUP 00
− How to use
Troubleshooting/inspection Service Points
− How to
Cope with Intermittent Malfunction
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
DIAGNOSIS
TSB Revision
WIRELESS CONTROL MODULE (WCM)
42C-35
DTC B2206: VIN code mismatch
.
DTC SET CONDITION
WCM sets DTC B2206 when VIN registered in it and
VIN that has been transmitted on the CAN bus do not
match.
.
TECHNICAL DESCRIPTION (COMMENT)
WCM determines that the abnormality is present
when VIN registered in it and the one that has been
transmitted on the CAN bus do not match.
.
TROUBLESHOOTING HINTS
• Malfunction of WCM
• VIN registered in engine control module
unmatched
• WCM being registered to another vehicle
DIAGNOSIS
Required Special Tools:
• MB991958 Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827 M.U.T.-III USB Cable
• MB991910 M.U.T.-III Main Harness A
STEP 1. Check the VIN registered in the engine control
module and the VIN of the vehicle.
Check if the VIN registered in the engine control module
matches with the VIN of the vehicle.
(1) On the system selection screen of the M.U.T.-III, select
"MFI/GDI/Diesel".
(2) Select "Coding."
(3) Select "VIN Information."
(4) Compare with the VIN of the vehicle.
Q: Does the VIN of the engine control module match with
the VIN of the vehicle?
YES : Go to Step 2.
NO : Write the VIN to the engine control module. [Refer to
GROUP 00
− How to Perform Vehicle Identification
Number (VIN) Writing
]. Record VIN and go to
Step 2 .
DIAGNOSIS
TSB Revision
WIRELESS CONTROL MODULE (WCM)
42C-36
STEP 2. Recheck for diagnostic trouble code.
Check again if the DTC is set to the WCM.
CAUTION
To prevent damage to scan tool (MB991958), always turn
the ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool (MB991958).
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Check if the DTC is set.
Q: Is the DTC set?
YES : Replace WCM and register the ID codes (Refer to
). After registering the ID codes, go to Step 3.
NO : The procedure is complete.
STEP 3. Recheck for diagnostic trouble code.
Check again if the DTC is set to the WCM.
(1) Turn the ignition switch to the "ON" position.
(2) Check if the DTC is set.
Q: Is the DTC set?
YES : Replace the engine control module and record the
VIN [Refer to GROUP 00
− How To Perform Vehicle
Identification Number (VIN) Writing
].
NO : The procedure is complete.
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст