Mitsubishi Evolution X. Manual — part 248
SEALANT
TSB Revision
ENGINE LUBRICATION
12-3
SEALANT
M1121000500827
Item
Specified sealant
Engine oil pressure switch
THREE BOND 1215 or 1212D or equivalent
LUBRICANTS
M1121000401715
Item
Engine oil
Quantity dm
3
(qt)
Oil filter
Engine oils displaying ILSAC certification
symbol ("Starburst" symbol) or conforming
to the API classification SM or higher
0.3 (0.32)
Oil cooler
0.5 (0.52)
Total quantity
5.6 (5.9)
ENGINE OIL
AC609011
ILSAC certification symbol
("Starburst" symbol)
AC
CAUTION
Never use nondetergent or straight mineral oil.
.
Use only engine oils displaying the ILSAC certification mark
("Starburst" symbol) on the container.
AC709997
API service symbol
AB
If these oils are not available, an API classification SM or
higher can be used.
SPECIAL TOOLS
TSB Revision
ENGINE LUBRICATION
12-4
SPECIAL TOOLS
M1121000601571
Tool
Tool number
and name
Supersession
Application
MB991610
MB991610
Oil filter wrench
Oil filter wrench
Removal and installation of engine oil
filter (When using oil filter MD356000)
MB992118
MB992118
Oil pressure
switch wrench
Oil pressure switch
wrench
Removal and installation of engine oil
pressure switch
B991346
MB991346
Top cover
wrench
−
Holding the engine oil pump sprocket
ON-VEHICLE SERVICE
ENGINE OIL CHECK
M1121000900955
AC205268
Maximum
Minimum
Good
AE
1. Pull out the oil dipstick, clean off the engine oil on the oil
dipstick, and then reinsert the oil dipstick.
2. Pull out the oil dipstick, and check the engine oil level is
within the marks on one side of the oil dipstick (engine cover
side).
NOTE:
.
•
Checking the oil might be difficult shortly after stopping
the engine or engine oil replacement.
•
If difficult, take some time (approx. 30 sec.) and try
again.
•
Refer to the information label indicating the engine oil
check process on the rocker cover.
3. Check that the engine oil is not excessively dirty, that there
is no coolant or gasoline mixed in, and that it is sufficiently
thick and slippery.
ON-VEHICLE SERVICE
TSB Revision
ENGINE LUBRICATION
12-5
ENGINE OIL REPLACEMENT
M1121001001992
1. Start the engine and allow it to warm up until the
temperature of the coolant reaches 80
− 90° C (176 − 194° F).
WARNING
Use care as oil could be hot.
2. Remove the engine oil filler cap.
3. Remove the engine room under cover extension. (Refer to
GROUP 51, Under Cover
4. Remove the drain plug to drain oil.
AC708804AB
Engine
oil pan side
Drain plug gasket
5. Install a new drain plug gasket so that it faces in the
direction shown in the illustration, and then tighten the drain
plug to the specified torque.
Tightening torque: 39
± 5 N⋅ m (29 ± 3 ft-lb)
AC710765AB
CAUTION
• Do not use conventional petroleum based motor oil.
Using conventional motor oil may cause engine or tur-
bocharger damage.
• Do not used "blends" of conventional oil and synthetic
oil.
• If engine oil other than 5W-30 is used, the engine may
be seized by poor lubrication.
6. Refill the specified quantity of oil.
Specified Engine Oil: Engine oils displaying ILSAC
certification symbol ("Starburst" symbol) or con-
forming to the API classification SM or higher
Total quantity: 5.6 dm
3
(5.9 quarts)
7. Install the engine oil filler cap.
8. Let the engine run for a few minutes.
9. Stop the engine, and then check the oil level using the oil
dipstick after a few minutes.
10.Install the engine room under cover extension. (Refer to
GROUP 51, Under Cover
ENGINE OIL FILTER REPLACEMENT
M1121001101450
1. Start the engine and allow it to warm up until the
temperature of the coolant reaches 80
− 90° C (176 − 194° F)
WARNING
Use care as oil could be hot.
2. Remove the engine oil filler cap.
3. Remove the engine room under cover extension. (Refer to
GROUP 51, Under Cover
4. Remove the drain plug to drain oil.
AC103249AL
MB991610
or equivalent
ON-VEHICLE SERVICE
TSB Revision
ENGINE LUBRICATION
12-6
5. Use the respective tool in the following table to remove the
engine oil filter.
Number
Special tool
MD356000
Oil filter wrench
(MB991610) or
equivalent
6. Clean the filter bracket side mounting surface and ensure
the old O-ring has been removed.
AC103250 AG
O-ring
7. Apply a small amount of engine oil to the O-ring of the new
oil filter.
8. Screw on the oil filter by hand until it touches the surface of
the flange and then tighten it with an oil filter wrench.
Number
Special tool
Tightening
torque
MD356000
MB991610 or
equivalent
Approximately
3/4 turn [14
± 2
N
⋅ m (124 ± 17
in
−lb)]
9. Install the drain plug and refill engine oil. (Refer to
).
10.Rev the engine a few times, and check to be sure that no
engine oil leaks at the oil filter.
11.Install the engine room under cover extension. (Refer to
GROUP 51, Under Cover
OIL PRESSURE CHECK
M1121002301747
1. Check engine oil level.
AK703776 AE
Engine oil pressure
switch
Throttle body
2. Remove the engine oil pressure switch. (Refer to Oil
Pressure Switch Removal And Installation
3. Install the engine oil pressure gauge.
NOTE: Use a 1/8 pipe thread adapter.
4. Run the engine to warm it.
5. After the engine has been warmed up, check that engine oil
pressure is within the standard value.
Standard value:
At idle: 29 kPa (4.2 psi) or more
At 3,500 r/min: 294
− 686 kPa (43 − 100 psi)
6. Remove the engine oil pressure gauge.
7. Install the engine oil pressure switch. (Refer to Oil Pressure
Switch Removal And Installation
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст