Mitsubishi Evolution X. Manual — part 580
DIAGNOSIS
TSB Revision
KEYLESS OPERATION SYSTEM (KOS)
42B-227
STEP 4. Check the wiring harness between the unlock
sensor (front door: RH) connector E-05 (terminal Nos. 4, 2,
6) and the ground for short circuit.
(1) Disconnect unlock sensor (front door: RH) connector E-05,
and check the wiring harness.
(2) Check the wiring harness between unlock sensor (front
door: RH) connector E-05 (terminal No. 4) and ground
OK: No continuity
(3) Check the wiring harness between unlock sensor (front
door: RH) connector E-05 (terminal No. 2) and ground
OK: No continuity
(4) Check the wiring harness between unlock sensor (front
door: RH) connector E-05 (terminal No.6) and ground.
OK: No continuity
Q: Is the wiring harness between unlock sensor (front
door: RH) connector E-05 (terminal Nos. 4, 2, 6) and the
ground in good condition?
YES : Go to Step 5.
NO [unlock sensor (front door: RH) connector E-05
terminal No.4
− ground.] : Repair the wiring harness
between unlock sensor (front door: RH) connector
E-05 (terminal No.4) and ground.
NO [unlock sensor (front door: RH) connector E-05
terminal No.2
− ground.] : Repair the wiring harness
between unlock sensor (front door: RH) connector
E-05 (terminal No.2) and the ground.
NO [unlock sensor (front door: RH) connector E-05
terminal No.6
− ground.] : Repair the wiring harness
between unlock sensor (front door: RH) connector
E-05 (terminal No.6) and the ground.
AC709707IT
Harness side: E-05
AC709707IU
Harness side: E-05
AC209731
AC208731CQ
Harness side: E-05
DIAGNOSIS
TSB Revision
KEYLESS OPERATION SYSTEM (KOS)
42B-228
STEP 5. KOS communication test
Using scan tool (M.U.T-III), perform the antenna communica-
tion test to check that the exterior transmitter antenna (passen-
ger's side) communicates normally (Refer to
Q: Is the check result normal?
YES : Go to Step 6.
NO : Perform troubleshooting for the diagnostic trouble
code No. B240B (Refer to
).
STEP 6. Check of the troubles
Operate the unlock sensor (front door: RH) and check that the
door can be locked.
Q: Is the check result normal?
YES : The diagnosis is complete.
NO : Replace KOS-ECU and register the ID codes (Refer
to
DIAGNOSIS
TSB Revision
KEYLESS OPERATION SYSTEM (KOS)
42B-229
Inspection Procedure 13: Trunk lid opener switch does not work.
CAUTION
Before replacing the ECU, ensure that the power
supply circuit, the ground circuit and the com-
munication circuit are normal.
AC609043
KOS-ECU
TRUNK LID
OPENER
SWITCH
RED
BLUE- YELLO
W
BLUE- YELLO
W
BLUE- YELLO
W
BLA
CK
BLA
CK
Trunk Lid Opener Switch Circuit
AC
AC708950AW
C-42
Connectors: C-05, C-42
C-05
AC708955AL
Connector: D-17
D-17 (BR)
DIAGNOSIS
TSB Revision
KEYLESS OPERATION SYSTEM (KOS)
42B-230
.
TROUBLESHOOTING HINTS
• Malfunction of the exterior transmitter antenna
assembly (trunk lid)
• Malfunction of the trunk lid opener switch
• Damaged wiring harness and connectors
• Malfunction of the KOS-ECU
DIAGNOSIS
Required Special Tools:
• MB992006: Extra fine probe
• MB991223: Harness set
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicles Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A
STEP 1. Using scan tool MB991958, read the diagnostic
trouble code.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958. Refer to "How to connect
scan tool (M.U.T.-III)
(2) Turn the ignition switch to the "ON" position.
(3) Check whether the KOS-ECU related DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES : Diagnose the KOS-ECU. Refer to
.
NO : Go to Step 2.
AC708970AG
Connectors: F-09, F-27
F-09
F-27
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст