Mitsubishi Evolution X. Manual — part 1121
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-119
.
FUNCTION
If a failure is present in the wiring harness between
the joint connector (CAN2) and the joint connector
(CAN3), this diagnosis result will be set.
.
TROUBLE JUDGEMENT CONDITIONS
If a communication flag is not set for some of the
ECUs on the CAN-C line, the ETACS-ECU deter-
mines that there is a failure.
.
TROUBLESHOOTING HINTS
• Malfunction of the connector [joint connector
(CAN2), joint connector (CAN3) or intermediate
connector failed]
• Malfunction of the wiring harness [open circuit
between joint connector (CAN2) and joint con-
nector (CAN3)]
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB992006: Extra Fine Probe
STEP 1. Check joint connector (CAN2) C-104, joint
connector (CAN3) C-127 and intermediate connector C-131
for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
CAUTION
The strand end of the twisted wire should be within 10 cm
(4 inches) from the connector. For details refer to
Q: Are joint connector (CAN2) C-104, joint connector
(CAN3) C-127 and intermediate connector C-131 in good
condition?
YES : Go to Step 2.
NO : Repair the damaged parts.
AC708950BY
C-104
C-131
Connectors: C-104, C-131
AC708951CC
Connector: C-127
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-120
STEP 2. Check the wiring harness between joint connector
(CAN2) C-104 and joint connector (CAN3) C-127 for open
circuit.
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
(1) Disconnect joint connector (CAN2) C-104 and joint
connector (CAN3) C-127, and check the wiring harness.
(2) Check the wiring harness between joint connector (CAN2)
C-104 (terminal 4) and joint connector (CAN3) C-127
(terminal 5)
OK: Continuity exists (2
Ω or less)
(3) Check the wiring harness between joint connector (CAN2)
C-104 (terminal 15) and joint connector (CAN3) C-127
(terminal 16)
OK: Continuity exists (2
Ω or less)
Q: Is the wiring harness between joint connector (CAN2)
C-104 and joint connector (CAN3) C-127 in good
condition?
YES : The trouble can be an intermittent malfunction (Refer
to GROUP 00, How to use
Troubleshooting/inspection Service Points
− How to
Cope with Intermittent Malfunction
NO : Repair the wiring harness between joint connector
(CAN2) C-104 and joint connector (CAN3) C-127.
AC709707BR
TEST
HARNESS
Harness side: C-104
TEST
HARNESS
Harness side: C-127
AC709707BS
Harness side: C-104
Harness side: C-127
TEST HARNESS
TEST
HARNESS
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-121
DIAGNOSTIC ITEM 14: Diagnose the lines between joint connector (CAN3) and joint connector
(CAN4). <TC-SST>
CAUTION
When servicing a CAN bus line, ground yourself by touching a metal object such as an unpainted
water pipe. If you fail to do so, a component connected to the CAN bus line may be damaged.
TRANSAXLE
ASSEMBLY
ENGINE
CONTROL
MODULE
CAN-C Communication Circuit <TC-SST>
ETACS-ECU
INTERFACE
CIRCUIT
CAN DRIVE
CIRCUIT
JOINT CONNECTOR
(CAN2)
JOINT CONNECTOR
(CAN3)
JOINT CONNECTOR
(CAN4)
SHIFT LEVER
ASC-ECU
STEERING
WHEEL SENSOR
S-AWC-ECU
NOTE
: THE TERMINAL NUMBERS DESCRIBED
IN THE CIRCUIT DIAGRAM AGREE WITH
THE NUMBERS MAKED ON THE
TRANSAXLE ASSEMBLY CONNECTOR AND
HARNESS SIDE CONNECTOR.
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-122
.
FUNCTION
If a failure is present in the wiring harness between
the joint connector (CAN3) and the joint connector
(CAN4), this diagnosis result will be set.
.
TROUBLE JUDGEMENT CONDITIONS
If a communication flag is not set for some of the
ECUs on the CAN-C line, the ETACS-ECU deter-
mines that there is a failure.
.
TROUBLESHOOTING HINTS
• Malfunction of the connector [joint connector
(CAN3), joint connector (CAN4) or intermediate
connector failed]
• Malfunction of the wiring harness [open circuit
between joint connector (CAN3) and joint con-
nector (CAN4)]
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB992006: Extra Fine Probe
STEP 1. Check joint connector (CAN3) C-127, joint
connector (CAN4) A-14 and intermediate connector A-13
for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
CAUTION
The strand end of the twisted wire should be within 10 cm
(4 inches) from the connector. For details refer to
Q: Are joint connector (CAN3) C-127, joint connector
(CAN4) A-14 and intermediate connector A-13 in good
condition?
YES : Go to Step 2.
NO : Repair the damaged parts.
AC708949AL
Connectors: A-13, A-14
A-14
A-13
AC708951CC
Connector: C-127
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст