Mitsubishi Evolution X. Manual — part 775
DIAGNOSIS
TSB Revision
ACTIVE SKID CONTROL SYSTEM (ASC)
35C-107
STEP 6. Resistance measurement at A-05 ASC-ECU
connector
(1) Disconnect the ASC-ECU connector, connect the ASC
check harness (Special tool: MB991997) to the wiring
harness-side connector, and then measure at the special
tool connector side.
NOTE: Do not connect the special tool to ASC-ECU.
(2) Measure the resistance between the wheel speed sensor
circuit power supply terminal (signal terminal) No. 36 and
the body ground as well as between the ground terminal
No. 37 and the body ground.
OK: No continuity
Q: Is the check result normal?
YES : Go to Step 9.
NO (Not normal at the terminal No. 36 or 37) : Go to Step
7.
STEP 7. Connector check: A-05 ASC-ECU connector, C-45
intermediate connector, D-18 wheel speed sensor <RL>
connector
Q: Is the check result normal?
YES : Go to Step 8.
NO : Repair the defective connector. Then go to Step 17.
STEP 8. Wiring harness check between A-05 ASC-ECU
connector terminal No. 36 and D-18 wheel speed sensor
<RL> connector terminal No. 1, and between A-05
ASC-ECU connector terminal No. 37 and D-18 wheel speed
sensor <RL> connector terminal No. 2
• Short circuit check of wheel speed sensor <RL> circuit
Q: Is the check result normal?
YES : Replace the wheel speed sensor <RL>. (Refer to
.) Then go to Step 17.
NO : Repair the wiring harness. Then go to Step 17.
AC400817CI
ASC-ECU
MB991997
Check harness
A-05 ASC-ECU
harness connector
DIAGNOSIS
TSB Revision
ACTIVE SKID CONTROL SYSTEM (ASC)
35C-108
STEP 9. Voltage measurement at A-05 ASC-ECU connector
(1) Disconnect the ASC-ECU connector, connect the ASC
check harness (Special tool: MB991997) to the
ASC-ECU-side connector and the wiring harness-side
connector, and then measure at the special tool connector
side.
(2) Turn the ignition switch to the ON position.
(3) Measure the voltage between the wheel speed sensor
circuit power supply terminal (signal terminal) No. 36 and
the body ground.
OK: System voltage
Q: Is the check result normal?
YES : Go to Step 10.
NO : Go to Step 12.
STEP 10. Wiring harness check between A-05 ASC-ECU
connector terminal No. 36 and D-18 wheel speed sensor
<RL> connector terminal No. 1, and between A-05
ASC-ECU connector terminal No. 37 and D-18 wheel speed
sensor <RL> connector terminal No. 2
• Open circuit check of wheel speed sensor <RL> circuit
Q: Is the check result normal?
YES : Go to Step 11.
NO : Repair the wiring harness. Then go to Step 17.
STEP 11. Check of wheel speed sensor as a single unit
Refer to
.
Q: Is the check result normal?
YES : Go to Step 13.
NO : Replace the wheel speed sensor <RL>. (Refer to
.) Then go to Step 17.
STEP 12. Connector check: A-05 ASC-ECU connector,
C-45 intermediate connector, D-18 wheel speed sensor
<RL> connector
Q: Is the check result normal?
YES : Go to Step 16.
NO : Repair the defective connector. Then go to Step 17.
AC400817CJ
ASC-ECU
MB991997
Check harness
A-05 ASC-ECU
harness connector
DIAGNOSIS
TSB Revision
ACTIVE SKID CONTROL SYSTEM (ASC)
35C-109
STEP 13. Check of wheel speed sensor installation status
Check the installation status of wheel speed sensor <RL> (dis-
connection of wheel speed sensor, looseness of mounting bolt,
etc.).
Q: Is the check result normal?
YES : Go to Step 14.
NO : Reinstall the wheel speed sensor <RL> correctly.
(Refer to
STEP 14. Wheel bearing looseness check
NOTE: Wheel bearing looseness may increase the gap
between the wheel speed sensor and the wheel speed detec-
tion magnet encoder. Check the wheel bearing <RL> for loose-
ness. (Refer to GROUP 27
−
On-vehicle Service
.)
Q: Is the check result normal?
YES : Go to Step 15.
NO : Replace the rear wheel hub assembly. (Refer to
GROUP 27
− Rear Axle Hub Assembly
STEP 15. Check of wheel speed detection encoder
Check the encoder for adhesion of foreign materials or defor-
mation.
Q: Is the check result normal?
YES : Go to Step 16.
NO (Adhesion of foreign materials) : Clean the encoder
so as not to disturb the magnetization pattern on the
encoder while taking care of the magnet, magnetic
substance, and magnetic attraction.
NO (Deformation) : Replace the rear wheel hub assembly.
(Refer to GROUP 27
− Rear Axle Hub Assembly
.)
STEP 16. Check whether the DTC is reset.
Drive the vehicle at 12mph (20 km/h) or more.
NOTE: The ABS warning light does not turn OFF in some
cases unless the vehicle runs at 12mph (20 km/h) or higher.
Q: Is DTC C1048 set?
YES : Replace the hydraulic unit (incorporates in
.) Then go to Step 17.
NO : Intermittent malfunction. (Refer to GROUP 00
− How
to Cope with Intermittent Malfunction
.)
STEP 17. Check whether the DTC is reset.
Drive the vehicle at 12mph (20 km/h) or more.
NOTE: The ABS warning light does not turn OFF in some
cases unless the vehicle runs at 12mph (20 km/h) or higher.
Q: Is DTC C1048 set?
YES : Return to Step 1.
NO : This diagnosis is complete.
AC608248AB
Magnetic
encoder
Rear Wheel
bearing
Rear wheel
hub
assembly
DIAGNOSIS
TSB Revision
ACTIVE SKID CONTROL SYSTEM (ASC)
35C-110
DTC C1049: RR wheel speed sensor control phase time exceeded
CAUTION
• If there is any problem in the CAN bus lines, an incor-
rect diagnostic trouble code may be set. Prior to this
diagnosis, diagnose the CAN bus lines.
• Whenever the ECU is replaced, ensure that the CAN
bus lines are normal.
• When the hydraulic unit (integrated with ASC-ECU) is
replaced, always perform the calibration of steering
wheel sensor, G and yaw rate sensor, brake fluid pres-
sure sensor, cut valve, and inlet valve.(Refer to
.)
.
CIRCUIT OPERATION
• Each wheel speed detecting section is a kind of a pulse
generator. It consists of the encoder (plate on which the
north and south pole of magnet are arranged alternately) for
detecting the wheel speed, which rotates at the same speed
of the wheels, and the wheel speed sensor. This detecting
section outputs the frequency pulse signals in proportion to
the wheel speed.
• The pulse signals generated by the wheel speed detecting
section are sent to ASC-ECU. ASC-ECU uses the fre-
quency of the pulse signals to determine the wheel speed.
.
AC708948
Connector: A-05
A-05 (B)
AB
AC708950
Connector: C-47
AE
AC708955
Connector: D-09
D-09 (B)
AH
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст