Mitsubishi Evolution X. Manual — part 577
DIAGNOSIS
TSB Revision
KEYLESS OPERATION SYSTEM (KOS)
42B-215
STEP 3. Check the wiring harness between the KOS-ECU
connector C-05 (terminal Nos. 24, 36) and unlock sensor
(front door: LH) connector E-18 (terminal Nos. 4, 2), and
between unlock sensor (front door: LH) connector E-18
(terminal No. 6) and ground for open circuit.
(1) Disconnect KOS-ECU connector C-05 and unlock sensor
(front door: LH) connector E-18, and check the wiring
harness.
(2) Check the wiring harness between KOS-ECU connector
C-05 (terminal No.24) and unlock sensor (front door: LH)
connector E-18 (terminal No.4).
OK: Continuity exists (2
Ω or less)
(3) Check the wiring harness between KOS-ECU connector
C-05 (terminal No.36) and unlock sensor (front door: LH)
connector E-18 (terminal No.2).
OK: Continuity exists (2
Ω or less)
(4) Check the wiring harness between unlock sensor (front
door: LH) connector E-18 (terminal No.6) and ground.
OK: Continuity exists (2
Ω or less)
Q: Is the wiring harness between KOS-ECU connector C-05
(terminal Nos. 24, 36) and unlock sensor (front door:
LH) connector E-18 (terminal Nos. 4, 2), and between
unlock sensor (front door: LH) connector E-18 (terminal
No. 6) and ground in good condition?
YES : Go to Step 4.
NO (KOS-ECU connector C-05 terminal No.24
− unlock
sensor (front door: LH) connector E-18 terminal No.4.) :
Repair the wiring harness between KOS-ECU
connector C-05 (terminal No.24) and unlock sensor
(front door: LH) connector E-18 (terminal No.4).
NO (KOS-ECU connector C-05 terminal No.36
− unlock
sensor (front door: LH) connector E-18 terminal No.2.) :
Repair the wiring harness between KOS-ECU
connector C-05 (terminal No.36) and unlock sensor
(front door: LH) connector E-18 (terminal No.2).
NO (unlock sensor (front door: LH) connector E-18
terminal No.6
− ground.) : Repair the wiring harness
between unlock sensor (front door: LH) connector
E-18 (terminal No.6) and ground.
AC709707
Harness side: C-05
GK
Harness side: E-18
AC709707GL
Harness side: C-05
Harness side: E-18
AC209731
Connector E-18
(harness side)
AC208731CG
DIAGNOSIS
TSB Revision
KEYLESS OPERATION SYSTEM (KOS)
42B-216
STEP 4. Check the wiring harness between the unlock
sensor (front door: LH) connector E-18 (terminal Nos. 4, 2,
6) and the ground for short circuit.
(1) Disconnect unlock sensor (front door: LH) connector E-18,
and check the wiring harness.
(2) Check the wiring harness between unlock sensor (front
door: LH) connector E-18 (terminal No. 4) and ground
OK: No continuity
(3) Check the wiring harness between unlock sensor (front
door: LH) connector E-18 (terminal No. 2) and ground
OK: No continuity
(4) Check the wiring harness between unlock sensor (front
door: LH) connector E-18 (terminal No.6) and ground.
OK: No continuity
Q: Is the wiring harness between unlock sensor (front
door: LH) connector E-18 (terminal Nos. 4, 2, 6) and the
ground in good condition?
YES : Go to Step 5.
NO [unlock sensor (front door: LH) connector E-18
terminal No.4
− ground.] : Repair the wiring harness
between unlock sensor (front door: LH) connector
E-18 (terminal No.4) and ground.
NO [unlock sensor (front door: LH) connector E-18
terminal No.2
− ground.] : Repair the wiring harness
between unlock sensor (front door: LH) connector
E-18 (terminal No.2) and the ground.
NO [unlock sensor (front door: LH) connector E-18
terminal No.6
− ground.] : Repair the wiring harness
between unlock sensor (front door: LH) connector
E-18 (terminal No.6) and the ground.
AC709707IR
Harness side: E-18
AC709707IS
Harness side: E-18
AC209731
AC208731CN
Harness side: E-18
DIAGNOSIS
TSB Revision
KEYLESS OPERATION SYSTEM (KOS)
42B-217
STEP 5. KOS communication test
Using scan tool (M.U.T-III), perform the antenna communica-
tion test to check that the exterior transmitter antenna (driver's
side) communicates normally (Refer to
Q: Is the check result normal?
YES : Go to Step 6.
NO : Perform troubleshooting for the diagnostic trouble
code No. B240A (Refer to
).
STEP 6. Check of the troubles
Operate the unlock sensor (front door: LH) and check that the
door can be locked.
Q: Is the check result normal?
YES : The diagnosis is complete.
NO : Replace KOS-ECU and register the ID codes (Refer
to
Inspection Procedure 11: Front passenger's door lock switch does not work.
CAUTION
Before replacing the ECU, ensure that the power
supply circuit, the ground circuit and the com-
munication circuit are normal.
AC709309
KOS-ECU
LOCK SWITCH
(FRONT DOOR: RH)
BLA
CK
BLA
CK
BLA
CK
BLA
CK
ORANGE
YELLO
W
-BLUE
Lock Switch (Front Door: RH) Circuit
AB
DIAGNOSIS
TSB Revision
KEYLESS OPERATION SYSTEM (KOS)
42B-218
.
TROUBLESHOOTING HINTS
• Malfunction of the exterior transmitter antenna
assembly (front passenger's side)
• Malfunction of the lock switch (front door: RH)
• Damaged wiring harness and connectors
• Malfunction of the KOS-ECU
DIAGNOSIS
Required Special Tools:
• MB992006: Extra fine probe
• MB991223: Harness set
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicles Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A
AC708950AZ
Connector: C-05
AC708951AX
C-116
C-117 (BR)
Connectors: C-116, C-117
AC608168 AC
Connector: E-06
E-06 (GR)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст