Mitsubishi Evolution X. Manual — part 875
STEERING WHEEL
TSB Revision
POWER STEERING
37-23
Required Special Tools:
• MB990784: Ornament Remover
• MB990803: Steering wheel puller
REMOVAL SERVICE POINTS
.
<<A>> COVER REMOVAL
AC505865AB
MB990784
Cover
Insert the special tool MB990784 at the indicated position to
remove the cover.
NOTE: The special tool MB990784 can be inserted through the
notch behind the area shown.
.
11. Garnish
12. Cruise control switch
connector connection
13. Cruise control switch
14. AWC switch connector
connection <Except with
steering wheel audio remote
control switch>
15. AWC switch <Except with
steering wheel audio remote
control switch>
16. Steering wheel audio remote
control switch connector
connection <Vehicles with
steering wheel audio remote
control switch>
Removal steps (Continued)
17. Steering wheel audio remote
control switch <Vehicles with
steering wheel audio remote
control switch>
<<
D
>>
>>
A
<<
18. Steering wheel assembly
Removal steps (Continued)
STEERING WHEEL
TSB Revision
POWER STEERING
37-24
<<B>> AIR BAG MODULE CONNECTOR
CONNECTION REMOVAL
AC605948
AC600868
AI
Lower column cover
Driver's air bag
module connector
(4-pin, yellow)
Horn connector
Outer housing of the
driver's air bag module connector
Slide the outer housing of the driver’s air bag module connector
in the arrow direction shown and disconnect the connector.
.
<<C>> DRIVER’S AIR BAG MODULE REMOVAL
CAUTION
• Never use an electric tester to diagnose the air bag
module circuit. Never attempt to disassemble the air
bag module.
• Store the removed air bag module in a clean, dry place
with the pad surface facing upward.
• When discarding the air bag module, deploy the air bag
as specified in the service procedure. (Refer to GROUP
52B
− Air bag Module Disposal Procedure
.)
•
AC704972 AB
Equal to or more than
40mm (1.6 inch).
With the driver's air bag module mounting torx screw,
loosen the screw, but do not remove it.
Using the torx wrench (T30), remove the driver's air bag mod-
ule.
.
STEERING WHEEL
TSB Revision
POWER STEERING
37-25
<<D>> STEERING WHEEL ASSEMBLY REMOVAL
1. Position the steering wheel in a straight ahead position.
CAUTION
• Use the special tool to remove the steering wheel since
the steering column collision adsorbing mechanism
may be damaged.
2.
AC705717AB
MB990803
Use special tool MB990803 to remove the steering wheel.
INSTALLATION SERVICE POINTS
.
>>A<< STEERING WHEEL ASSEMBLY INSTALLA-
TION
After centering the clock spring (Refer to 52B
− Air bag module
clock spring ), install the steering wheel assembly.
.
>>B<< AIR BAG MODULE CONNECTOR
CONNECTION/AUDIO CONTROL SWITCH
CONNECTOR CONNECTION/HORN CONNECTOR
CONNECTION INSTALLATION
Connect the connector securely and route the harnesses not to
lie off the cover hole.
STEERING SHAFT
TSB Revision
POWER STEERING
37-26
STEERING SHAFT
REMOVAL AND INSTALLATION
M1372011500953
CAUTION
• Before removing the steering wheel assembly and driver's air bag module/knee air bag module,
always refer to GROUP 52B
− Service Precautions
and Air bag Module and Clock Spring
.)
• After installation, perform a calibration for the ASC-ECU to learn the steering wheel sensor neutral
point. (Refer to GROUP 35C
− On-vehicle Service, Steering Wheel Sensor Calibration
.)
Pre-removal Operation
• Steering wheel at straight-ahead position check
• Steering wheel assembly removal (Refer to
• Instrument panel cover lower removal (Refer to GROUP
52A
− Instrument Lower Panel
.) <MR>
• Knee air bag module removal (Refer to GROUP 52B −
Driver's Knee Air Bag Module
.)
Post-installation Operation
• Instrument panel cover lower installation (Refer to
GROUP 52A
− Instrument Lower Panel
.) <MR>
• Steering wheel assembly installation (Refer to
.)
• Steering wheel straight-ahead position check
AC709222 AB
5
9
3
2
7
1
8
4
11
2.5 ± 0.5 N·m
23 ± 4 in-lb
12 ± 3 N·m
9 ± 2 ft-lb
28 ± 7 N·m
21 ± 5 ft-lb
5
3
10
A
A
B
B
C
C
5
3
5
3
7.0 ± 3.0 N·m
62 ± 27 in-lb
6
Section A-A
Claw
Section C-C
Claw
Section B-B
Claw
Note: claw position is symmetrical
20 ± 5 N·m
15 ± 3 ft-lb
2.5 ± 0.5 N·m
23 ± 4 in-lb
Removal steps
<<
A
>>
1. Knob cap <Vehicles with
KOS>
2. Ignition key cover
3. Steering column lower cover
4. Steering column protector
•
Receiver antenna module
removal (Refer to GROUP
42B
− Exterior Transmitter
Antenna Assembly, Interior
Transmitter Antenna
Assembly, Receiver Antenna
Module
<Vehicles with KOS>
Removal steps (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст