Mitsubishi Evolution X. Manual — part 100

BATTERY

TSB Revision

CHASSIS ELECTRICAL

54A-3

DATA LINK CONNECTOR

BATTERY

GENERAL INFORMATION

M2544200200383

The sealed battery is installed in the trunk room. The
sealed battery has a structure that uses the sealed
reaction (cathodic absorption), eliminating the needs
for refilling and liquid level check.

• The sealed reaction (cathodic absorption) brings

the oxygen gas

*

, which is generated at positive

pole, to the negative pole, and binds the oxygen
gas with hydrogen gas generated at negative
pole. As a result, the gas is transformed back to
water, preventing the decrease of electrolytic
solution.

NOTE:

*

: The generation of oxygen gas at posi-

tive pole occurs in an earlier stage than that of
hydrogen gas at negative pole.

• Calcium alloy with superior characteristics of

electrolyte decrease is used for the polar plate
grille between the positive and negative poles in
the battery container.

Although the sealed reaction (cathodic absorption)
occurs with 100% efficiency with a normal use, the
generated gas may not be absorbed completely
under the statuses of overcharging, high tempera-
ture, or high voltage. Therefore, to prevent the charg-
ing of non-absorbed inflammable gas inside the trunk
room, the battery exhaust tube (battery cover hose)
and pipe for gas bleeding are equipped.

Data link connector

Terminal
No.

Connection content

1

Diagnosis control

2, 3

−

4

Ground

5

Ground

6

CAN communication line (CAN_H)

7

ECM

8

ECM

9

−

10

Pulse check

11

− 13

−

14

CAN communication line (CAN_L)

15

−

16

Battery power supply

AC608435

AC608434

AD

9

1

11

3

2

10

12

4

14

6

5

13

15

7 8

16

Data link connector

AC705447AC

pipe

Battery exhaust tube
(Battery cover hose)

BATTERY

TSB Revision

CHASSIS ELECTRICAL

54A-4

CAUTION

• When charging, always set the charging current to 5 amps or less.
• Always charge the battery by referencing the charging time in Graph 1.
• Do not remove the battery cover or label.
• Always securely mount the battery exhaust tube (battery cover hose) and pipe.

Graph 1

Item

S65D26L

Voltage V

12

Capacity (5-hour rate) Ah

44

AC707780

12.8

12.6

12.4

12.2

12.0

11.8

11.6

13.0

0

2

4

6

8

10

12

(V)

Battery voltage (V)

Batter

y charging time at 5 amps (h)

(h)

S65D26L

LIGHTING

TSB Revision

CHASSIS ELECTRICAL

54A-5

LIGHTING

EXTERIOR LIGHTS

M2544300300451

.

CONSTRUCTION DIAGRAM

• As for headlight assembly, a type with halogen

bulbs for the high-beam and low-beam and a type
with a discharge bulb for both high-beam and
low-beam are established.

• The halogen bulb type headlight assembly

employs the four-light type integrated with the
headlight (low-beam), headlight (high-beam),
front turn-signal light, and position light. The
dimmed headlight (low-beam) is also used as a
daytime running light. <Standard: GSR>
NOTE: For the operation of daytime running light,
refer to Function and Control by ETACS-ECU

P.54A-10

.

• For the discharge bulb type headlight assembly,

the headlight assembly with two headlights has
been adopted which incorporates the projector
type headlight (low-beam/high-beam), daytime
running light, front turn-signal light, and position
light. Also, the headlight manual leveling system
(refer to ) has been adopted. The switching of
headlight (low-beam/high-beam) is performed by
the driving of light-shield in the projector unit
using the signal from lighting switch. <Standard:
MR, Option: GSR>
NOTE: For the operation of daytime running light,
refer to Function and Control by ETACS-ECU

P.54A-10

.

AC709102

Headlight (Low-beam)
<Vehicles without discharge headlight>

Position light (Front side-marker
light and reflector)

Headlight (High-beam / low-beam)
<Vehicles with discharge headlight>

Headlight (High-beam)
<Vehicles without discharge headlight>

Daytime running light
<Vehicles with discharge headlight>

Front turn-signal light

Side turn-signal light

Headlight
assembly

AB

Front fog light

AC709103

Stop/taillight

Rear turn-signal
light

Taillight assembly

License plate light

High-mounted stop light

Rear
combination light
assembly

AB

Rear side-marker
light and reflector

Back-up light

Taillight

LIGHTING

TSB Revision

CHASSIS ELECTRICAL

54A-6

• The front fog light is mounted to the front bumper.

• The side turn-signal lights have been installed to

the fender.

• The rear combination light assembly are inte-

grated with the stop/taillight, rear turn-signal light
and rear side-marker light.

• The taillight assembly are integrated with the tail-

light and back-up light.

• The LED type high-mounted stoplight has been

integrated into the trunk lid.

• The lighting system is provided with headlight

automatic-shutdown function, auto light function
and daytime running light function (Refer to Func-
tion and Control by ETACS-ECU

P.54A-10

).

• For the flasher timer function of turn-signal, the

comfort flasher function has been adopted to
improve the operability when changing lanes.
When the turn-signal light switch (lighting switch)
is operated for a short time, this function flashes
the turn-signal light of the operated direction
three times (Refer to Function and Control by
ETACS-ECU

P.54A-10

).

.

SPECIFICATIONS

NOTE: The brackets ( ) show the ANSI Trade No. or
bulb type.

Item

Specification

Headlight assembly <Vehicles without
discharge headlight>

High-beam <Halogen bulb>

60W (9005 or HB3)

Low-beam <Halogen bulb>

51W (9006 or HB4)

Position light

5W (WY5W)

Front turn-signal light

21W (WY21W)

Headlight assembly <Vehicles with
discharge headlight>

High-beam / low-beam <Discharge bulb>

35W (D2S)

Daytime running light

27W / 32cp (1156)

Position light

5W (WY5W)

Front turn-signal light

21W (WY21W)

Front fog light

55W (H11)

Side turn-signal light

5W

Rear combination light assembly

Stop/taillight

21 / 5W (7443)

Rear turn-signal light

21W (7440)

Rear side-marker light

5W (W5W)

Taillight assembly

taillight

5W (W5W)

Back-up light

21W (7440)

High-mounted stoplight

LED type

License plate light

5W (W5W)