Mitsubishi Evolution X. Manual — part 236
RADIATOR
TSB Revision
ENGINE COOLING
14-31
RADIATOR
REMOVAL AND INSTALLATION
M1141001502141
Pre-removal operation
• Engine Room Under Cover Front A and Engine Room
Under Cover Center Removal (Refer to GROUP 51,
Under Cover
• Engine coolant Draining (Refer to
• Charge Air Cooler Intake Hose B and Charge Air Cooler
Intake Pipe B Removal (Refer to GROUP 15, Charge Air
Cooler
).
Post-installation operation
• Charge Air Cooler Intake Hose B and Charge Air Cooler
Intake Pipe B Installation (Refer to GROUP 15, Charge
).
• Engine coolant Refilling and Check (Refer to
• Engine Room Under Cover Front A and Engine Room
Under Cover Center Installation (Refer to GROUP 51,
Under Cover
AC710570
9.5 ± 3.5 N·m
84 ± 31 in-lb
3
4
5
6
7
15
15
16
1
2
17
8
10
9
23
24
25
20
21
27
26
12
11
17
AB
N
14
18
4.0 ± 2.0 N·m
36 ± 17 in-lb
19
22
4.4 ± 0.5 N·m
43 ± 4 in-lb
3.4 ± 0.5 N·m
31 ± 4 in-lb
9.5 ± 3.5 N·m
84 ± 31 in-lb
9.5 ± 3.5 N·m
84 ± 31 in-lb
3.4 ± 0.5 N·m
31 ± 4 in-lb
4.4 ± 0.5 N·m
43 ± 4 in-lb
13
13
Radiator removal steps
1.
Radiator drain plug
2.
O-ring
3.
Radiator cap
4.
Radiator condenser tank hose
<<
A
>>
>>
A
<<
5.
Radiator upper hose
6.
Radiator cap assembly
<<
A
>>
>>
A
<<
7.
Radiator upper hose
<<
A
>>
>>
A
<<
8.
Radiator lower hose
<<
A
>>
>>
A
<<
9.
Radiator lower hose
10. Radiator lower pipe assembly
11. Radiator fan motor connector
connection
12. Condenser fan motor connector
connection
•
Front end upper bar (Refer to
GROUP 42, Loose Panel
<<
B
>>
13. Bracket
<<
B
>>
14. Fan, fan motor and fan shroud
assembly
15. Support upper insulator
16. Radiator assembly
17. Support lower insulator
18. Radiator condenser tank hose
Radiator removal steps
RADIATOR
TSB Revision
ENGINE COOLING
14-32
REMOVAL SERVICE POINTS
.
<<A>> RADIATOR UPPER HOSE/RADIATOR
LOWER HOSE REMOVAL
Make mating marks on the radiator hose and the hose clamp.
Disconnect the radiator hose.
.
<<B>> BRACKET/FAN, FAN MOTOR AND FAN
SHROUD ASSEMBLY REMOVAL
Remove the fan, fan motor, and fan shroud assembly from the
radiator assembly with the following steps.
1. Remove the bracket.
2. Release the upper locks of the radiator assembly from the
fan, fan motor, and fan shroud assembly.
3. Slightly raise the fan, fan motor, and fan shroud assembly.
4. Release the lower locks of the radiator assembly from the
fan, fan motor, and fan shroud assembly. Then, remove the
fan, fan motor, and fan shroud assembly from the radiator
assembly.
19. Radiator condenser tank hose
20. Radiator condenser tank
21. Radiator condenser tank pipe
22. Radiator condenser tank bracket
Fan shroud removal steps
4.
Radiator condenser tank hose
<<
A
>>
>>
A
<<
5.
Radiator upper hose
6.
Radiator cap assembly
11. Radiator fan motor connector
12. Condenser fan motor connector
•
Front end upper bar (Refer to
GROUP 42, Loose Panel
<<
B
>>
13. Bracket
<<
B
>>
14. Fan, fan motor and fan shroud
assembly
23. Radiator fan
24. Radiator fan motor
25. Condenser fan
26. Condenser fan motor
27. Fan shroud
Radiator removal steps
AC200641AD
Mating marks
AC708620AC
(2)
(2)
(3)
(4)
(4)
Fan shroud assembly
Radiator assembly
RADIATOR
TSB Revision
ENGINE COOLING
14-33
INSTALLATION SERVICE POINT
.
>>A<< RADIATOR LOWER HOSE/RADIATOR
UPPER HOSE INSTALLATION
1. Insert each hose as far as the projection of the water inlet
fitting, water outlet fitting or radiator.
2. Align the mating marks on the radiator hose and hose
clamp, and then connect the radiator hose.
AC200642
Mating
marks
Projection
Radiator, water inlet
fitting or water outlet
fitting
AY
NOTES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст