Mitsubishi Evolution X. Manual — part 470
KEY INTERLOCK AND SHIFT LOCK MECHANISMS
TSB Revision
TWIN CLUTCH- SPORTRONIC SHIFT TRANSMISSION (TC-SST)
22C-337
KEY INTERLOCK AND SHIFT LOCK MECHANISMS
REMOVAL AND INSTALLATION
M1225009800017
Pre-removal Operation
• Floor console bracket (A) and floor console side cover
removal (Refer to GROUP 52A
− Floor Console Assembly
.)
• Instrument panel cover lower removal <Leather combina-
tion interior package (Vehicles without side air bag)>
(Refer to GROUP 52A
− Instrument Lower Panel
.)
• Steering column lower cover removal (Refer to GROUP
37
− Steering Shaft
• Foot duct (driver's side) removal (Refer to GROUP 55 −
Post-installation Operation
• Foot duct (driver's side) installation (Refer to GROUP 55 −
• Steering column lower cover installation (Refer to GROUP
37
− Steering Shaft
• Instrument panel cover lower installation <Leather combi-
nation interior package (Vehicles without side air bag)>
(Refer to GROUP 52A
− Instrument Lower Panel
.)
• Floor console bracket (A) and floor console side cover
installation (Refer to GROUP 52A
− Floor Console
Assembly
.)
• Key interlock mechanism check (Refer to
• Shift lock mechanism check (Refer to
.)
• Shift lever operation check (Refer to
AC705527
AC709660AB
2
1
5
3
4
Removal steps
1.
Band clip
2.
Wiring harness clip
>>
B
3.
Key interlock cable
connection (shift lever side)
<<
A
>>
>>
A
4.
Key interlock cable
connection (steering side)
5.
Key interlock cable
Removal steps
KEY INTERLOCK AND SHIFT LOCK MECHANISMS
TSB Revision
TWIN CLUTCH- SPORTRONIC SHIFT TRANSMISSION (TC-SST)
22C-338
REMOVAL SERVICE POINTS
.
<<A>> KEY INTERLOCK CABLE (STEERING
SIDE) REMOVAL
Turn the ignition switch to the ACC position and then pull the
key interlock cable out from the ignition key cylinder.
INSTALLATION SERVICE POINTS
.
>>A<< KEY INTERLOCK CABLE (STEERING
SIDE) INSTALLATION
Turn the ignition switch to the ACC position and then install the
key interlock cable to the ignition key cylinder.
.
>>B<< KEY INTERLOCK CABLE (SHIFT LEVER
SIDE) INSTALLATION
CAUTION
Leave the ignition switch in the LOCK (OFF) position until
the key interlock cable installation is completed.
1. Move the shift lever to the P position, and turn the ignition
switch to the LOCK (OFF) position.
2. Install the tip of key interlock cable to the lock cam of shift
lever assembly, using a caution not to twist the inner cable.
3. Install the adjuster case with its lock guide pulled up
(unlocked).
4. Firmly push down the lock guide to lock it.
NOTE: The lock position of the key interlock cable is auto-
matically adjusted by a spring.
AC707937
AC707782
AD
Inner cable
Key interlock cable
A
Spring
Lock
Key interlock cable
Lock guide
Lock guide
View A
Lock cam
Unlock
TRANSFER ASSEMBLY
TSB Revision
TWIN CLUTCH- SPORTRONIC SHIFT TRANSMISSION (TC-SST)
22C-339
TRANSFER ASSEMBLY
REMOVAL AND INSTALLATION
M1225010000015
Pre-removal Operation
• Engine compartment under cover front B assembly
removal (Refer to GROUP 51
− Under Cover
• Transfer oil draining (Refer to
Post-installation Operation
• ACD air bleeding (Refer to
• Transfer oil filling (Refer to
.)
• Engine compartment under cover front B assembly instal-
lation (Refer to GROUP 51
− Under Cover
.)
AC707653AC
4
3
12
5
7
6
9
8
10
1
2
2
12
N
N
11
Gear oil:
Hypoid gear oil
API classification
GL-5 SAE90
10 ± 2 N·m
89 ± 17 in-lb
10 ± 2 N·m
89 ± 17 in-lb
25 ± 4 N·m
19 ± 3 ft-lb
44 ± 5 N·m
33 ± 3 ft-lb
<OILED>
26 ± 4 N·m
20 ± 2 ft-lb
<DRIED>
34 ± 5 N·m
26 ± 3 ft-lb
9 ± 1 N·m
80 ± 8 in-lb
69 ± 9 N·m
51 ± 7 ft-lb
10 ± 3 N·m
89 ± 26 in-lb
45 ± 6 N·m
33 ± 4 ft-lb
69 ± 9 N·m
51 ± 7 ft-lb
5.0 ± 2.0 N·m
45 ± 17 in-lb
53 ± 8 N·m
40 ± 5 ft-lb
69 ± 9 N·m
51 ± 7 ft-lb
20 ± 5 N·m
15 ± 3 ft-lb
47 ± 11 N·m
35 ± 8 ft-lb
54 ± 5 N·m
40 ± 3 ft-lb
Fluid:
DIA QUEEN
ATF SP III
Removal steps
1.
Front floor backbone brace
<<
A
>>
2.
Front propeller shaft
assembly
•
Front driveshaft assembly,
output shaft assembly
(Refer to GROUP 26
−
Driveshaft assembly
•
Center member and front
roll stopper assembly (Refer
to GROUP 32
− Engine Roll
Stopper and Center Member
•
Front exhaust pipe (Refer to
GROUP 15
− Exhaust Pipe
and Main Muffler
3.
Rear roll stopper center bolt
4.
Dynamic damper
5.
Driveshaft heat protector
6.
Transfer heat protector
Removal steps
TRANSFER ASSEMBLY
TSB Revision
TWIN CLUTCH- SPORTRONIC SHIFT TRANSMISSION (TC-SST)
22C-340
REMOVAL SERVICE POINTS
.
<<A>> FRONT PROPELLER SHAFT ASSEMBLY
REMOVAL
Make mating marks on the front propeller shaft assembly and
companion flange, then remove the connecting nut.
.
<<B>> TRANSFER ASSEMBLY REMOVAL
Move the engine and transaxle assembly toward the front of
the vehicle to create a gap between the engine/transaxle
assembly and the crossmember. Pull out the transfer assembly
through this gap.
INSTALLATION SERVICE POINTS
.
>>A<< TRANSFER PRESSURE HOSE ASSEMBLY
INSTALLATION
CAUTION
When installing the transfer pressure hose assembly, use
caution that the assembly does not interfere with sur-
rounding components.
7.
Transfer pressure hose
assembly connection
8.
Steering gear and linkage
heat protector
9.
Turbocharger protector A
Removal steps
<<
B
>>
10. Transfer assembly
>>
A
11. Transfer pressure hose
assembly
12. O-ring
Removal steps
AC708894AC
Mating marks
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст