Mitsubishi Evolution X. Manual — part 990
RADIO AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-321
STEP 6. Check the wiring harness between ETACS-ECU
connector C-317 (terminal 1) and radio and CD player
connector C-107 (terminal 30).
• Check the power supply lines (battery power supply) for
open circuit and short circuit.
Q: Is the wiring harness between ETACS-ECU connector
C-317 (terminal 1) and radio and CD player connector
C-107 (terminal 30) in good condition?
YES : Go to Step 7.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary.
STEP 7. Check the power supply circuit to the ETACS-ECU.
Measure the voltage at ETACS-ECU connector C-307.
(1) Disconnect the connector, and measure at the wiring
harness-side connector.
(2) Measure the voltage between terminal 2 and ground.
OK: Battery voltage
Q: Is the measured voltage battery voltage?
YES : Go to Step 9.
NO : Go to Step 8.
STEP 8. Check the wiring harness between ETACS-ECU
connector C-307 (terminal 2) and fusible link (36)
• Check the power supply line for open circuit and short cir-
cuit.
Q: Is the wiring harness between ETACS-ECU connector
C-307 (terminal 2) and fusible link (36) in good
condition?
YES : Go to Step 9.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary.
STEP 9. Retest the system
Check if the radio and CD player power is turned ON.
Q: Is the check result normal?
YES : The trouble can be an intermittent malfunction (Refer
to GROUP 00, How to use
Troubleshooting/inspection Service Points
− How to
Cope with Intermittent Malfunction
NO : Replace the radio and CD player.
AC709325 AD
Harness side: C-307
RADIO AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-322
Inspection Procedure 2: No sound is heard. <Vehicles with audio amplifier>
CAUTION
Before replacing the ECU, ensure that the power supply circuit, the ground circuit and the communi-
cation circuit are normal.
Audio Amplifier System Circuit
RELAY
BOX
AUDIO AMPLIFIER
FUSIBLE
LINK
36
RADIO AND CD PLAYER
RADIO AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-323
.
COMMENTS ON TROUBLE SYMPTOM
If the audio sound is not output, the radio and CD
player, audio amplifier, or power supply circuit of
audio amplifier may have a problem, or the option
coding information may be inconsistent.
.
PROBABLE CAUSES
• The radio and CD player may be defective
• The audio amplifier may be defective
• Option coding information inconsistency
• Damaged harness wires and connectors
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB992006: Extra Fine Probe
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A
AC708951BE
C-109
C-24
Connectors: C-24, C-109
AC708950
Connector: C-47
AE
AC708954 AR
Connectors: D-29, D-30
D-30
D-29
RADIO AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-324
STEP 1. Check the ETACS-ECU coding data.
(1) Operate the scan tool MB991958 to read the ETACS-ECU
option coding information (Refer to GROUP 00, Coding
Table
(2) Check that the "Speaker" is set to "Premium."
Q: Is the check result normal?
YES : Go to Step 2.
NO : Operate scan tool MB991958 to set the option coding
"Speaker" to "Premium," and check the trouble
symptom.
STEP 2. Check audio amplifier connector D-29 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is audio amplifier connector D-29 in good condition?
YES : Go to Step 3.
NO : Repair or replace the damaged component(s) (Refer
to GROUP 00E, Harness Connector Inspection
STEP 3. Check the ground circuit to the audio amplifier.
Measure the resistance at audio amplifier connector D-29.
(1) Disconnect audio amplifier connector D-29, and measure
the resistance available at the wiring harness side of the
connector.
(2) Measure the resistance between terminal 24 and ground.
OK: The resistance should be 2 ohms or less
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
AC709322 AT
Harness side: D-29
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст