Mitsubishi Evolution X. Manual — part 1103
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-47
STEP 16. Using scan tool MB991958, diagnose the CAN
bus line. (checking the shift lever for internal short)
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Disconnect shift lever connector C-27.
(2) Connect scan tool MB991958 to the data link connector.
(3) Turn the ignition switch to the "ON" position.
(4) Diagnose CAN bus lines, and check if the scan tool
MB991958 screen is as shown in the figure.
OK: The display of the scan tool MB991958 is as
shown in the figure.
Q: Does scan tool MB991958 screen correspond to the
illustration?
YES : Repair the wiring harness between shift lever
connector C-27 and joint connector (CAN3) C-127.
NO : Check shift lever connector C-27, and repair if
necessary. If the shift lever connector is in good
condition, replace the shift lever.
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
AC709542 AC
: Red section on screen
M.U.T.
J/C (3)
J/C (2)
KOS/WCM
SRS
A/C
AUDIO
MMCS
Sat Radio
HFM
OCM
METER
ASC
ENGINE
J/C (1)
ETACS
<M/T>
SAS
S-AWC
AC709543 AC
: Red section on screen
M.U.T.
J/C (3)
J/C (2)
KOS/WCM
SRS
A/C
AUDIO
MMCS
Sat Radio
HFM
OCM
METER
ASC
LEVER
J/C (1)
ETACS
<TC-SST>
SAS
S-AWC
J/C (4)
TC-SST
ENGINE
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-48
STEP 17. Using scan tool MB991958, diagnose the CAN
bus line. (checking the TC-SST-ECU for internal short)
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Disconnect transaxle assembly connector B-107.
(2) Connect scan tool MB991958 to the data link connector.
(3) Turn the ignition switch to the "ON" position.
(4) Diagnose CAN bus lines, and check if the scan tool
MB991958 screen is as shown in the figure.
OK: The display of the scan tool MB991958 is as
shown in the figure.
Q: Does scan tool MB991958 screen correspond to the
illustration?
YES : Repair the wiring harness between transaxle
assembly connector B-107 and joint connector
(CAN4) A-14.
NO : Check transaxle assembly connector B-107, and
repair if necessary. If the transaxle assembly
connector is in good condition, replace the transaxle
assembly
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
AC709542 AC
: Red section on screen
M.U.T.
J/C (3)
J/C (2)
KOS/WCM
SRS
A/C
AUDIO
MMCS
Sat Radio
HFM
OCM
METER
ASC
ENGINE
J/C (1)
ETACS
<M/T>
SAS
S-AWC
AC709543 AC
: Red section on screen
M.U.T.
J/C (3)
J/C (2)
KOS/WCM
SRS
A/C
AUDIO
MMCS
Sat Radio
HFM
OCM
METER
ASC
LEVER
J/C (1)
ETACS
<TC-SST>
SAS
S-AWC
J/C (4)
TC-SST
ENGINE
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-49
STEP 18. Using scan tool MB991958, diagnose the CAN
bus line.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Diagnose CAN bus lines, and check if the scan tool screen
is as shown in the illustration.
Q: Does the scan tool screen correspond to the
illustration?
YES : The trouble can be an intermittent malfunction (Refer
to GROUP 00, How to use
Troubleshooting/inspection Service Points
− How to
Cope with Intermittent Malfunction
NO : Check ETACS-ECU connector C-301, and repair if
necessary. If the ETACS-ECU connector is in good
condition, replace the ETACS-ECU.
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
AC709542 AB
: Red section on screen
M.U.T.
J/C (3)
SAS
J/C (2)
KOS/WCM
SRS
A/C
AUDIO
MMCS
Sat Radio
HFM
OCM
METER
ASC
ENGINE
J/C (1)
ETACS
<M/T>
S-AWC
AC709543 AB
: Red section on screen
M.U.T.
J/C (3)
SAS
J/C (2)
KOS/WCM
SRS
A/C
AUDIO
MMCS
Sat Radio
HFM
OCM
METER
ASC
LEVER
ENGINE
J/C (1)
ETACS
<TC-SST>
S-AWC
TC-SST
J/C (4)
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-50
DIAGNOSTIC ITEM 4: Diagnose shorts in the ground to CAN-C bus line.
CAN-C Communication Circuit <M/T>
ETACS-ECU
INTERFACE
CIRCUIT
CAN DRIVE
CIRCUIT
JOINT CONNECTOR
(CAN2)
JOINT CONNECTOR
(CAN3)
ASC-ECU
STEERING
WHEEL SENSOR
S-AWC-ECU
ENGINE
CONTROL
MODULE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст