Mitsubishi Evolution X. Manual — part 211
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-13
HOW TO DIAGNOSE THE CAN BUS LINE
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A
1. Connect scan tool MB991958 to the data link connector.
2. Turn the ignition switch to the "ON" position.
3. Select the "CAN Bus Diagnosis" from the start-up screen.
4. When the vehicle information is displayed, confirm that it
matches the vehicle whose CAN bus lines will be
diagnosed.
• If they match, go to step 8.
• If not, go to step 5.
5. Select the "view vehicle information" button.
6. Enter the vehicle information and select the "OK" button.
7. When the vehicle information is displayed, confirm again
that it matches the vehicle which whose CAN bus lines will
be diagnosed.
• If they match, go to step 8.
• If not, go to step 5.
8. Press the "OK" button.
9. When the optional equipment screen is displayed, choose
the one which the vehicle is fitted with, and then select the
"OK" button.
10.Turn the ignition switch to the "LOCK" (OFF) position.
11.Disconnect scan tool MB991958.
DIAGNOSTIC TROUBLE CODE CHART
M1172002200897
Check according to the inspection chart that is
appropriate for the DTC.
DTC number
Inspection Item
Reference page
15
Cruise control switch system
22
Stoplight switch system
23
ECM and its related components
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-14
DIAGNOSTIC TROUBLE CODE PROCEDURES
DTC 15: Cruise Control Switch System
AC709181
ON/OFF
CANCEL
COAST/SET
ACC/RES
CLOCK
SPRING
ENGINE
CONTROL
MODULE
(ECM)
CRUISE
CONTROL
SWITCH
GREEN
GREEN-RED
YELLOW-GREEN
RED-YELLOW
RED-YELLOW
BLUE
AB
Cruise Control Switch System Circuit
AC709196 AB
B-10 (GR)
Connector: B-10
ECM
Air cleaner
AC709197
Connector: C-130
AB
C-130
(BR)
AC709198AB
C-201 (L)
C-202
C-205
Connectors: C-201, C-202, C-205
Clock spring
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-15
.
CIRCUIT OPERATION
This circuit judges the signals of each switch
("ON/OFF", "CANCEL", "COAST/SET" and
"ACC/RES") of the cruise control switch. The ECM
detects the state of the cruise control switch by sens-
ing the voltages shown below.
• When all switches are released: 4.7 − 5.0 volts
• When the "ON/OFF" switch is pressed: 0 − 0.5
volt
• When the "CANCEL" switch is pressed: 1.0 − 1.8
volts
• When the "COAST/SET" switch is pressed: 2.3 −
3.0 volts
• When the "ACC/RES" switch is pressed: 3.5 −
4.2 volts
.
DTC SET CONDITIONS
Check Condition
• The "CRUISE" indicator light illuminates.
JUDGMENT CRITERIA
• This DTC is set when the "COAST/SET" switch
or "ACC/RES" switch is stuck to ON.
.
TROUBLESHOOTING HINTS (THE MOST
LIKELY CAUSES FOR THIS CASE:)
• Damaged harness or connector.
• Malfunction of the cruise control switch.
• Malfunction of the clock spring.
• Malfunction of the ECM.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A
• MB991223: Harness Set
• MB992006: Extra Fine Probe
• MB992110: Power Plant ECU Check Harness
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-16
STEP 1. Using scan tool MB991958, check the data list
item 75: Cancel switch, item 86: Main switch, item 91:
Resume switch and item 92: Set switch.
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector
(Refer to
).
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to data reading mode for cruise
control system (Refer to
).
• Item 75: Cancel switch.
• When "CANCEL" switch is pressed, the display on
scan tool MB991958 should be "ON".
• When "CANCEL" switch is released, the display on
scan tool MB991958 should be "OFF".
• Item 86: Main switch.
• When "ON/OFF" switch is pressed, the display on
scan tool MB991958 should be "ON".
• When "ON/OFF" switch is pressed again, the display
on scan tool MB991958 should be "OFF".
• Item 91: Resume switch.
• When "ACC/RES" switch is pressed, the display on
scan tool MB991958 should be "ON".
• When "ACC/RES" switch is released, the display on
scan tool MB991958 should be "OFF".
• Item 92: Set switch.
• When "COAST/SET" switch is pressed, the display
on scan tool MB991958 should be "ON".
• When "COAST/SET" switch is released, the display
on scan tool MB991958 should be "OFF".
(4) Turn the ignition switch to the "LOCK" (OFF) position.
(5) Disconnect scan tool MB991958.
Q: Is the switch operating properly?
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст