Mitsubishi Evolution X. Manual — part 313
PRECAUTIONS BEFORE SERVICE
TSB Revision
GENERAL
00-27
HOW TO PERFORM VEHICLE IDENTIFICATION NUMBER (VIN) WRITING
M1001011400483
CAUTION
The F.A.S.T-Key (Free-hand Advanced Security
Transmitter) is described as the Keyless Opera-
tion System (KOS) in this manual. (KOS is indi-
cated as F.A.S.T. in the scan tool display.)
Follow the procedure below to register the VIN of the
Wireless Control Module (WCM) and the Keyless
Operation System (KOS).
The VIN is stored in the engine control module
(ECM), WCM, and the KOS-ECU. If the VIN is
improperly erased, the engine warning light or the
keyless operation system warning indicator illumi-
nate, and the diagnostic trouble code is displayed.
When the ECM, WCM, and the KOS-ECU are
replaced, follow the procedure below to write the
VIN.
AC700593
AE
Engine VIN Registration
Engine VIN Registration
Confirmation
OK
OK
OK
Engine VIN Registration
Completed
Result of Engine
VIN Registration
OK
F.A.S.T./IMMO/Keyless/TPMS
F.A.S.T./IMMO/Keyless/TPMS
VIN Registration
VIN Registration
Confirmation
VIN Registration
completed
Result of VIN
Registration
Screen frow of scan tool (M.U.T.- III)
<When ECM is replaced>
System Select
Special Function
Key Code Registration
OK
Key Code Registration
Completed
<When WCM or KOS-ECU are replaced>
System Select
Coding
OK
OK
PRECAUTIONS BEFORE SERVICE
TSB Revision
GENERAL
00-28
WRITING PROCEDURE
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A
CAUTION
Check that diagnostic trouble code P0603 "EEPROM fail"
is not set. When diagnostic trouble code P0603 "EEPROM
fail" is set, the ECM cannot store the key code even if the
key code is registered. If this diagnostic trouble code is
set, troubleshoot the ECM and repair. Then register the key
code to the ECM.
CAUTION
Before connecting or disconnecting the MB991958: Scan
Tool, turn the ignition switch to the "LOCK" (OFF) position.
Connect scan tool MB991958 to the 16-pin data link connector
as follows.
NOTE: For details on how to use scan tool MB991958, refer to
the "M.U.T.-III Owner's Manual."
1. Ensure that the ignition switch is at the "LOCK" (OFF)
position.
2. Start up the personal computer.
3. Connect special tool MB991827 to special tool MB991824
and the personal computer.
4. Connect special tool MB991910 to the special tool
MB991824.
5. Connect special tool MB991910 to the data link connector of
the vehicle.
6. Turn the special tool MB991824 power switch to the "ON"
position.
NOTE: When the special tool MB991824 is energized, the
special tool MB991824 indicator light will be illuminated in a
green color.
7. Start the "M.U.T.-III system" on the personal computer and
turn the ignition switch to the "ON" position.
8. Select "F.A.S.T./IMMO/Keyless/TPMS" button from the
"System Select" screen. Then, select the applicable option
code item and push the OK button.
9. Select "Special Function" on the next screen.
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
System Select
Select Model Year and System
System List
Model Year
Vehicle Information
Loading Option Setup
OPC
With Option
Option Name
IMMOBI & Keyless & TPMS
VF2
VF3
IMMOBI & F.A.S.T. & TPMS
Model Name
Model Year
Model Code
Up to 2005 MY
From to 2006 MY
1
2
3
4
5
6
7
8
9
10
MPI/GDI/Diesel
F.A.S.T./IMMO/Keyless/TPMS
AT/CVT/A-MT
ABS/ASC/ASTC
SAS
Multi Select 4WD
SRS Airbag
A/C
ETACS
Meter
AC609809
OK button
AB
PRECAUTIONS BEFORE SERVICE
TSB Revision
GENERAL
00-29
10.Select "ENG key code & VIN Reg." from the "Special
Function" screen.
11.Push the OK button after "ENG key code & VIN Reg." is
displayed.
12.Push the OK button after "Completed. Press the OK button
and move to VIN writing function." is displayed.
13.Enter the VIN of registering vehicle and push the OK button.
14.Push the OK button after "VIN Writing will start. Are you
sure?" is displayed.
15.Return to the previous screen and "In Progress" is displayed
at the lower-left corner on the screen.
16.Push the OK button after "Completed." is displayed.
17.VIN writing result is displayed.
18.Complete the scan tool MB991958.
19.Disconnecting the scan tool MB991958 is the reverse of the
connecting sequence, making sure that the ignition switch is
at the "LOCK" (OFF).
20.Push the OK button after "Completed." is displayed.
21.Terminate the scan tool MB991958.
22.Turn the ignition switch to the "LOCK" (OFF) position and
then disconnect scan tool MB991958.
System Select
Please select function.
Special Function
Key & F.A.S.T.- Key Reg.
Steering lock unit Reg.
Comm. Test
ENG key code & VIN Reg.
F.A.S.T./IMMO/Keyless/TPMS
Tire Pressure Sensor ID Check
Tire Pressure Sensor ID Registration
Tire Pressure Sensor Check
AC709284
AB
Option: When IMMOBI & F.A.S.T. & TPMS is selected
System Select
Please select function.
Special Function
Key Registration
Key Registration (Barcode No.)
Keyless ID Reg.
ENG key code & VIN Reg.
F.A.S.T./IMMO/Keyless/TPMS
Additional key registration
Tire Pressure Sensor ID Check
Tire Pressure Sensor ID Registration
Tire Pressure Sensor Check
AC709283
AB
Option: When IMMOBI & Keyless & TPMS is selected
AC709286
OK button
AB
AC709287
AC709285
PRECAUTIONS BEFORE SERVICE
TSB Revision
GENERAL
00-30
VIN WRITING STEPS FOR WCM AND KOS-ECU
CAUTION
Before the VIN registration to WCM and KOS-ECU, check
that the VIN of ECM and vehicle are matched.
CAUTION
Check that diagnostic trouble code B2416 "ECU internal
error" is not set. When diagnostic trouble code B2416
"ECU internal error" is set, the WCM and the KOS-ECU
cannot store the VIN even if the VIN is written. If this diag-
nostic trouble code is set, troubleshoot the WCM or the
KOS-ECU and repair. Then write the VIN to the WCM or the
KOS-ECU.
CAUTION
Before connecting or disconnecting the MB991958: Scan
Tool, turn the ignition switch to the "LOCK" (OFF) position.
Connect scan tool MB991958 to the 16-pin data link connector
as follows.
NOTE: For details on how to use scan tool MB991958, refer to
the "M.U.T.-III Owner's Manual."
1. Ensure that the ignition switch is at the "LOCK" (OFF)
position.
2. Start up the personal computer.
3. Connect special tool MB991827 to special tool MB991824
and the personal computer.
4. Connect special tool MB991910 to the special tool
MB991824.
5. Connect special tool MB991910 to the data link connector of
the vehicle.
6. Turn the special tool MB991824 power switch to the "ON"
position.
NOTE: When the special tool MB991824 is energized, the
special tool MB991824 indicator light will be illuminated in a
green color.
7. Start the "M.U.T.-III system" on the personal computer and
turn the ignition switch to the "ON" position.
8. Select "F.A.S.T./IMMO/Keyless/TPMS" button from the
"System Select" screen. Then, select the applicable option
code item and push the OK button.
9. Select "Coding" on the next screen.
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
System Select
Select Model Year and System
System List
Model Year
Vehicle Information
Loading Option Setup
OPC
With Option
Option Name
IMMOBI & Keyless & TPMS
VF2
VF3
IMMOBI & F.A.S.T. & TPMS
Model Name
Model Year
Model Code
Up to 2005 MY
From to 2006 MY
1
2
3
4
5
6
7
8
9
10
MPI/GDI/Diesel
F.A.S.T./IMMO/Keyless/TPMS
AT/CVT/A-MT
ABS/ASC/ASTC
SAS
Multi Select 4WD
SRS Airbag
A/C
ETACS
Meter
AC609809
OK button
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст